From: Erik Belz (ebelz@xxxxxxxxxx)
Date: Sat Apr 29 2000 - 18:22:03 GMT-3
Well there are some advantages to using AURP versus GRE.
1. AURP allows you to do an Appletalk unnumbered to reserve cab ranges and avoi
d an overlap
2. AURP send tickles messages (keepalives) every 90 seconds versus 10 seconds f
or RTMP updates
3. AURP works with non-cisco gear. So if you have to connect to other vendors s
tuff. Or just as a practice
I tend to use Industry standards to be on the safe side.
Erik
>>> John Garrett <John.Garrett.B@bayer.com> 04/28/2000 4:48:35 PM >>>
Is this question out of line?
Does anyone have an opinion on this?
I hear a lot of talk about using the AURP tunnels(& issues) and I don't see a
reason not to use the gre tunnel with address and cable range instead.
John
---------------------- Forwarded by John Garrett/IS/US/BAYER on 04/28/2000
04:38 PM ---------------------------
John Garrett/IS/US/BAYER@BAYER-US-NOTES@groupstudy.com on 04/28/2000 08:59:31
AM
Please respond to CN=John Garrett/OU=IS/OU=US/O=BAYER@BAYER-US-NOTES
Sent by: nobody@groupstudy.com
To: "DDA.RFC-822=ccielab@groupstudy.com/P=Internet/A= /C=us"@X400
cc:
Subject: Re: AppleTalk Tunnel
Regarding Appletalk tunnels,
What would be the reason to use an AURP tunnel over a gre tunnel with an
appletalk cable range & a zone?
They both seem to accomplish the same thing. Would the connectivity options
still remain the same?
John
"DDA.RFC-822=hughcyli@holybridge.com.cn/P=BAYER/A=TELEMAIL/C=US"@X400@groupstud
y
.com on 04/28/2000 05:10:52 AM
Please respond to
"DDA.RFC-822=hughcyli@holybridge.com.cn/P=BAYER/A=TELEMAIL/C=US"@X400
Sent by: nobody@groupstudy.com
To: "DDA.RFC-822=ccielab@groupstudy.com/P=Internet/A= /C=us"@X400,
"DDA.RFC-822=honsiong@hotmail.com/P=Internet/A= /C=us"@X400
cc:
Subject: Re: AppleTalk Tunnel
-------------------------------------------------------------------------------
-
-----------------
You don't need configure cable range
----- Original Message -----
From: hon-siong chan <honsiong@hotmail.com>
To: <ccielab@groupstudy.com>
Sent: Thursday, April 27, 2000 6:23 PM
Subject: AppleTalk Tunnel
> HI group,
>
> If I need to set-up appletalk tunnel using AURP encapsulation, is that right
> I need to configure the following:
>
> 1) Create an "interface tunnel 0"
> 2) Specify tunnel source & destination address
> 3) enable "tunnel mode" to AURP
> 4) Specify "appletalk protocol aurp" command
> 5) create an appletalk cable range for interface tunnel 0
>
> Do I need to also create appletalk zone for tunnel 0? Do I need to configure
> the same for opposite directly connected router too?
>
> Clarification on the above is much appreciated!
>
> Thanks GROUP!
>
> Regards
> HonSiong
>
>
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:23:16 GMT-3