From: Dawit Birhanu (dawit@xxxxxxxxxxxx)
Date: Wed Dec 29 1999 - 01:39:55 GMT-3
Hi,
Apple routing eigrp is configured globally. The AS numbers are unique for
each router (90 for R1 and 93 for R2). Also AppleTalk EIGRP is working
properly on the other interfaces of both routers. Moreover, IP works fine
over the FastEther connecting the two routers when AppleTalk is not
configured on interfaces connecting the two routers. I also tried RTMP
instead of EIGRP - still it doesn't work.
Dawit
On Tue, 28 Dec 1999, Brad Hedlund wrote:
> He wouldn't have been able to assign Appletalk cable-ranges or zones to the
> interfaces if 'appletalk routing' wasnt configured globally.
>
>
>
> Brad
>
>
>
> > -----Original Message-----
> > From: Naushad Prasla [mailto:naushad.prasla@sabre.com]
> > Sent: Tuesday, December 28, 1999 8:14 PM
> > To: Earl Aboytes; Dawit Birhanu; CCIE Lab group study
> > Subject: RE: AppleTalk on FastEthernet interface
> >
> >
> > Have you turned on AppleTalk Routing in Global config...Just curious..
> >
> > Naushad
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> > Earl Aboytes
> > Sent: Tuesday, December 28, 1999 6:11 PM
> > To: Dawit Birhanu; CCIE Lab group study
> > Subject: Re: AppleTalk on FastEthernet interface
> >
> >
> > Dawit,
> > Remember that EIGRP with Appletalk must have different AS numbers.
> > Earl Aboytes
> >
> > At 04:14 PM 12/28/99 -0500, Dawit Birhanu wrote:
> > >
> > >I connected two routers (R1 & R2) using a crossed-over cable
> > attached to
> > >FastEther port. Then I configured IP on both sides of the
> > routers and both
> > >interfaces were up/up. When I configured AppleTalk on both interfaces
> > >with EIGRP routing protocol, the interface on one of the routers (R2)
> > >changed its state to up/down after few seconds while the
> > interface on the
> > >other router (R1) remained in up/up state. Also IP
> > connectivity between
> > >R1 and R2 over the FastEther link is lost.
> > >
> > >Both routers are identical (7000). Both interfaces are configured
> > >identically (except, ofcourse, for the IP address). On R2 I
> > have configured
> > >AppleTalk on another FastEther interface, which is connected to a
> > >Catalyst switch, and it is working properly. On R1 I have configured
> > >AppleTalk on an ATM subinterface, and it is working properly.
> > >
> > >I have tried shut/no shut and also reloaded router R2. But
> > the interface
> > >is still in up/down state, after a brief up/up state while
> > AppleTalk is
> > >initializing.
> > >
> > >Has any one encountered a similar problem? Is this a bug or a
> > >misconfiguration? I have included the interface
> > configurations for both
> > >routers:
> > >
> > >R1
> > >====
> > >interface FastEthernet0/1
> > > ip address 192.168.25.1 255.255.255.0
> > > appletalk cable-range 551-600 581.33
> > > appletalk zone sis
> > > appletalk protocol eigrp
> > > no appletalk protocol rtmp
> > >
> > >R2
> > >===
> > >interface FastEthernet0/1
> > > ip address 192.168.25.2 255.255.255.0
> > > appletalk cable-range 551-600 572.48
> > > appletalk zone sis
> > > appletalk protocol eigrp
> > > no appletalk protocol rtmp
> > >
> > >
> > >Dawit
> > >
> > >
This archive was generated by hypermail 2.1.4 : Thu Jun 13 2002 - 08:22:00 GMT-3