RE: Router Interface

What is plugged into FastEthernet8? Ibm thinking that maybe the IP on
FastEthernet8 really need to be in VLAN1 and that the FastEthernet8 really
needs to be line FastEthernet1-7. I think that fastethernet 0 -8 are access
ports and Interface GigabyteEthernet0 is your WAN interface.

These links might help you out:

http://www.cisco.com/c/en/us/td/docs/routers/access/800/860-880-890/software/
configuration/guide/SCG880-860.pdf

http://www.cisco.com/c/en/us/td/docs/routers/access/800/software/configuratio
n/guide/SCG800Guide.html

Another note, you included your username and password. If they are real b
you should changing them once you have the system working.

Andy

From: Mateen Taj [mailto:taj.mateen_at_gmail.com]
Sent: Tuesday, July 22, 2014 10:08 AM
To: Andrew LaPorte
Cc: Cisco certification
Subject: Re: Router Interface

Dear Andrew,

Thank you very much, Please find below configuration of the router, I want all
L2 should get the IP from a DHCP pool

ip dhcp excluded-address 192.168.181.1
ip dhcp excluded-address 192.168.181.2
ip dhcp excluded-address 192.168.181.10
!
ip dhcp pool BIL_pool
 import all
 network 192.168.181.0 255.255.255.0
 dns-server 213.42.20.20
 default-router 192.168.181.1
 lease 8
!
!
ip cef
no ip domain lookup
ip domain name yourdomain.com <http://yourdomain.com>
no ipv6 cef
!
multilink bundle-name authenticated
!
license udi pid CISCO892-K9 sn FGL1651
!
!
interface BRI0
 no ip address
 encapsulation hdlc
 shutdown
 isdn termination multidrop
!
interface FastEthernet0
 no ip address
!
interface FastEthernet1
 no ip address
!
interface FastEthernet2
 no ip address
!
interface FastEthernet3
 no ip address
!
interface FastEthernet4
 no ip address
!
interface FastEthernet5
 no ip address
!
interface FastEthernet6
 no ip address
!
interface FastEthernet7
 switchport mode trunk
 no ip address
!
interface FastEthernet8
 ip address 192.168.181.1 255.255.255.0
 ip nat inside
 ip virtual-reassembly in
 ip tcp adjust-mss 1452
 duplex auto
 speed auto
!
interface GigabitEthernet0
 description ***physical interface bound to dialer0
 no ip address
 ip nat outside
 ip virtual-reassembly in
 duplex auto
 speed auto
 pppoe-client dial-pool-number 1
!
interface Vlan1
 description $ETH-SW-LAUNCH$$INTF-INFO-FE 1$
 no ip address
 ip tcp adjust-mss 1452
!
interface Dialer0
 ip address negotiated
 ip mtu 1492
 ip nat outside
 ip virtual-reassembly in
 encapsulation ppp
 dialer pool 1
 dialer-group 1
 ppp authentication chap pap callin
 ppp chap hostname bil
 ppp chap password 0 a83wikhr
 ppp pap sent-username bil password 0 a83wikhr
 no cdp enable
!
ip forward-protocol nd
!
!
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip nat inside source list 1 interface Dialer0 overload
ip nat inside source list acl1 pool pool1
ip route 0.0.0.0 0.0.0.0 Dialer0
!
access-list 1 permit 192.168.181.0 0.0.0.255
dialer-list 1 protocol ip permit
no cdp run
!
!
!
!
!
!
control-plane

On Tue, Jul 22, 2014 at 5:56 PM, Andrew LaPorte <andy_at_cloud9.net
<mailto:andy_at_cloud9.net> > wrote:

I can try to help.

I'm guessing you have some type of L3 address (VLAN) on the device. Is the
DHCP range, port and the L3 VLAN in address range? Is the access point
expecting the port in access or trunk mode?

If these do not help send me a copy of the config for the router and AP.

Andy

-----Original Message-----
From: nobody_at_groupstudy.com <mailto:nobody_at_groupstudy.com>
[mailto:nobody_at_groupstudy.com <mailto:nobody_at_groupstudy.com> ] On Behalf Of
Mateen Taj
Sent: Tuesday, July 22, 2014 8:57 AM
To: Cisco certification
Subject: Router Interface

Dear Expert,

I need your help to troubleshoot the router(cisco 892) , how to get a DHCP
IP on a L2 interface on the same router , i have connected an access point
on L2 interface but it is not taking the IP from a DHCP pool

Regards

Blogs and organic groups at http://www.ccie.net
Received on Tue Jul 22 2014 - 10:26:26 ART