Re: Image verification

i suspect config reg 2101 is not entertaining my boot command stored in
nvram ? i guess if i move to 2102 all should be fine with my boot command

On Mon, Nov 4, 2013 at 5:31 PM, Carlos G Mendioroz <tron_at_huapi.ba.ar> wrote:

> The Pitonisa says to check your memory requirements. Also, she needs to
> see the console log of a rebload sequence, that would help uncover the
> mood of the gods in your switching quadrant...
>
> Imran Ali @ 04/11/2013 10:55 -0300 dixit:
> > thanks for reply but why my boot command is not working and it is
> > always booting with first image ..
> >
> >
> > On Mon, Nov 4, 2013 at 2:10 PM, Antonio Soares <amsoares_at_netcabo.pt>
> wrote:
> >
> >> Use the verify /md5 to be completely sure.
> >>
> >> By default the 4500's have confreg=2101, you need to change it to 2102.
> >>
> >>
> >>
> >> Regards,
> >>
> >> Antonio Soares, CCIE #18473 (R&S/SP)
> >> amsoares_at_netcabo.pt
> >> http://www.ccie18473.net
> >>
> >>
> >> -----Original Message-----
> >> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
> >> Imran Ali
> >> Sent: segunda-feira, 4 de Novembro de 2013 06:32
> >> To: Cisco certification
> >> Subject: OT: Image verification
> >>
> >> Hi all
> >>
> >> i have uploaded an image and i have done verification .
> >>
> >> core1#verify cat4500-entservicesk9-mz.122-54.SG1.bin
> >>
> >>
> CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
> >> C
> >>
> >>
> CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
> >> C
> >>
> >>
> CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
> >> C
> >>
> >>
> CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
> >> C
> >>
> >>
> CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
> >> C
> >>
> >>
> CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
> >> C
> >>
> >>
> CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
> >> C
> >> CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC
> >> Verified cat4500-entservicesk9-mz.122-54.SG1.bin
> >> SV-TS202-BB1#
> >>
> >>
> >> 1) what does this verification mean ? does it mean that
> checksum is
> >> ok ?
> >>
> >> or is it safe now to delete old image and reload so that it
> >> boots with this image.
> >>
> >> this is cat4506..
> >>
> >>
> >>
> >> 2) i have tried to set boot preference to new image ..but still it
> is
> >> booting with old image ..
> >> core1#show run | in boot
> >> boot system flash bootflash:cat4500-entservicesk9-mz.122-54.SG1.bin
> >>
> >> the issue is boot command is excepting any thing i type and not
> verifying
> >> its syntax..
> >>
> >> core1(config)#boot system flash abc
> >> core1(config)#
> >>
> >>
> >> what is the correct syntax .
> >>
> >>
> >> Blogs and organic groups at http://www.ccie.net
> >>
> >> _______________________________________________________________________
> >> Subscription information may be found at:
> >> http://www.groupstudy.com/list/CCIELab.html
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> >
> >
> >
> >
> >
>
> --
> Carlos G Mendioroz <tron_at_huapi.ba.ar> LW7 EQI Argentina

Blogs and organic groups at http://www.ccie.net
Received on Mon Nov 04 2013 - 17:38:29 ART