Re: NAT question on ASA 8.3 or above

Do you have other types of NAT statements, as then the order could be
important

On Wed, Jul 31, 2013 at 2:51 PM, Ryan West <rwest_at_zyedge.com> wrote:

> Probably have a dynamic nat before your static. Does it work for inbound,
> but not outbound?
>
> Sent from handheld.
>
> On Jul 31, 2013, at 8:31 AM, "Sadiq Yakasai" <sadiqtanko_at_gmail.com> wrote:
>
> > Hi Myung-Soo,
> >
> > Your config looks good to me. See below a similar one I tested some time
> > back.
> >
> > Perhaps something else on the configuration is interfering here? Can we
> see
> > full configuration?
> >
> > HTH,
> > Sadiq
> >
> > ASA5585(config)#
> > ASA5585(config)#
> > ASA5585(config)# sh run obje
> > ASA5585(config)# sh run object
> > object network NATTED_SUBNET
> > subnet 10.82.6.128 255.255.255.192
> > object network INSIDE_SUBNET
> > subnet 10.82.6.0 255.255.255.192
> > ASA5585(config)#
> > ASA5585(config)#
> > ASA5585(config)#
> > ASA5585(config)#
> > ASA5585(config)# sh run nat
> > !
> > object network INSIDE_SUBNET
> > nat (inside,outside) static NATTED_SUBNET
> > ASA5585(config)#
> > ASA5585(config)#
> > ASA5585(config)#
> > ASA5585(config)# sh nat
> >
> > Auto NAT Policies (Section 2)
> > 1 (inside) to (outside) source static INSIDE_SUBNET NATTED_SUBNET
> > translate_hits = 2804, untranslate_hits = 2785
> > ASA5585(config)#
> > ASA5585(config)#
> > ASA5585(config)# sh ver
> >
> > Cisco Adaptive Security Appliance Software Version 8.4(2)11
> > Device Manager Version 6.3(5)
> >
> >
> >
> >
> > On Wed, Jul 31, 2013 at 11:08 AM, Myung-Soo Ko <bacchus21_at_gmail.com>
> wrote:
> >
> >> Hello, Group
> >>
> >> I'm currently working on NAT configuration on ASA 8.3, but my old
> >> configuration didn't work on newer version.
> >>
> >> I checked configuration guide and modified the following static NAT
> >> configuration.
> >> =====================================================================
> >> Old(pre 8.3): static (outside,inside) 10.1.1.1 192.168.1.1 netmask
> >> 255.255.255.255
> >>
> >> New(8.3): object network obj-192.168.1.1
> >> host 192.168.1.1
> >> nat(outside, inside) static 10.1.1.1
> >> =====================================================================
> >> I think it's correct configuration, but it didn't work properly. Any
> >> correction? Please advise.
> >>
> >>
> >> I have another configuration need to be checked. Please refer to the
> >> following.
> >> ===========================================================
> >> object-group network CLIENTS_REAL
> >> network-object 172.16.0.0 255.255.0.0
> >>
> >> nat (inside,outside) source dynamic CLIENTS_REAL interface
> >> ===========================================================
> >> In this case, I think configuration should remain the same on pre 8.3
> and
> >> 8.3. Any opinion??
> >>
> >> It would be greatly appreciated if anyone can give me some advice.
> >>
> >> Regards,
> >> ----------------------------------------------
> >> "An open mind opens doors."
> >> 夢は信じていれば必ず叶う瘢雹瘢雹！！！
> >> Myung-Soo Ko (高 巳６柑洙)
> >>
> >>
> >> Blogs and organic groups at http://www.ccie.net
> >>
> >> _______________________________________________________________________
> >> Subscription information may be found at:
> >> http://www.groupstudy.com/list/CCIELab.html
> >
> >
> > --
> > CCIEx2 (R&S|Sec) #19963
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Wed Jul 31 2013 - 15:56:31 ART