OT: DSP Issue on CME

Hello,
Really new to cisco voip so please i will appreciate if you guys can
help me out on this. I have a cisco 2801 router which is acting as my
gateway with a PSTN line terminated on one of my FXO port. Now i did
the basic configuration to allow the PSTN line to ring on one of my
Cisco IP Phone. Here is the configuration

voice-port 0/0/0
connection plar opx 1001
signal groundstart

ephone-dn 10
number 10001

ephone 3
button 1:10

dial-peer voice 30 pots
destination-pattern 9T
port 0/0/0

Now what i noticed on the router is that after booting up the FXO port
still remains amber which means there is an issue with the PVDM
installed on the router if i am right. Used this link to confirm the
status of the interface:
http://www.cisco.com/en/US/docs/routers/access/2800/hardware/installation/guide/07_hw.html
Also used a new vic2-4fxo card just to be very sure it wasnt the FXO
card that was mal-functioning but still couldnt resolve this issue.

I now did some basic testing and here are the output:-

sh voice dsp detailed

Warning! DSPs1, in slot 0 are using non-default firmware from flash:
This is not recommended, the default version is 22.5.0

----------------------------FLEX VOICE CARD 0 ------------------------------
                           *DSP VOICE CHANNELS*

CURR STATE : (busy)inuse (b-out)busy out (bpend)busyout pending
LEGEND : (bad)bad (shut)shutdown (dpend)download pending

DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS
ABRT PACK COUNT
===== === == ========= ========== ===== ======= === == ========= ==
==== ============
C5510 001 01 None 0.0.0 bad idle 0 0
0 0/0
C5510 001 02 None 0.0.0 bad idle 0 0
0 0/0
C5510 001 03 None 0.0.0 bad idle 0 0
0 0/0
C5510 001 04 None 0.0.0 bad idle 0 0
0 0/0
C5510 001 05 None 0.0.0 bad idle 0 0
0 0/0
C5510 001 06 None 0.0.0 bad idle 0 0
0 0/0
C5510 001 07 None 0.0.0 bad idle 0 0
0 0/0
C5510 001 08 None 0.0.0 bad idle 0 0
0 0/0
                           *DSP SIGNALING CHANNELS*
DSP DSP DSPWARE CURR BOOT PAK TX/RX
TYPE NUM CH CODEC VERSION STATE STATE RST AI VOICEPORT TS
ABRT PACK COUNT
===== === == ========= ========== ===== ======= === == ========= ==
==== ============
C5510 001 01 {flex} 0.0.0 free idle 0 0 0/0/0
0 0/0
C5510 001 02 {flex} 0.0.0 free idle 0 0 0/0/1
0 0/0
C5510 001 03 {flex} 0.0.0 free idle 0 0 0/0/2
0 0/0
C5510 001 04 {flex} 0.0.0 free idle 0 0 0/0/3
0 0/0
------------------------END OF FLEX VOICE CARD 0 ----------------------------

ICT_Soln#sh voice dsp group all
DSP groups on slot 0:
dsp 1:
  State: FAIL, firmware: 0.0.0
  Max signal/voice channel: 8/8
  Max credits: 160
  num_of_sig_chnls_allocated: 4
  Transcoding channels allocated: 0
  Group: FLEX_GROUP_VOICE, complexity: FLEX
    Shared credits: 160, reserved credits: 0
    Signaling channels allocated: 4
    Voice channels allocated: 0
    Credits used: 0

  0 DSP resource allocation failure

Lastly did a voice test driver:-

DSP Keepalive Status Display:
=============================
DSP 1 is not UP, State: 5, Keepalive Sent: 0, Skip 0
DSP 2 Not Exist
DSP 3 Not Exist
DSP 4 Not Exist
DSP 5 Not Exist
DSP 6 Not Exist
DSP 7 Not Exist
DSP 8 Not Exist

I have cleaned up the PVDM and even inserted it into another slot but
still not able to make this work. Please how do resolve this issue?

Thanks inadvance.

Blogs and organic groups at http://www.ccie.net
Received on Sat Feb 16 2013 - 14:03:39 ART