Re: OSPF on 32 bit dialer interface

Tauseef,

Try to remove the no peer neighbor-route command, you configured the
virtual-template interface as /24 and you give the dialer side /32 host route.
When you remove the no peer neighbor command, you will install /32 host route
on each side. also as Joe said you don't have to configure ospf networks
type.

Try this and let me know what will happen.

--
Mohammad Mousa
CCIE 336990
On Nov 28, 2012, at 2:24 PM, Tauseef Khan wrote:
> sorry made a mistake in pasting
> ip local-pool 6.6 172.31.255.254
>
> !
> peer default ip address 6.6
>
> Regrads
>
> On 28 November 2012 11:22, Mohammad Mousa <mohd-mousa_at_hotmail.com> wrote:
> Before I lab it up, I noticed your pool name is different than of you've
called it.
>
>> nterface Virtual-Template16
>
>> peer default ip address pool 1.6
>
>
>> ip local-pool 6.6 172.31.255.254
>
> Did you receive ip address on the Dialer side?
>
> --
> Mohammad Mousa
> CCIE #36990
>
>
>
> On Nov 28, 2012, at 2:03 PM, Tauseef Khan wrote:
>
>> Please find below the configs
>> server:R1
>>
>> bba-group pppoe CISCO
>>  virtual-template 16
>> !
>> interface Gigabit0/0
>>  no ip address
>>  ip ospf network point-to-multipoint
>>  ip ospf mtu-ignore
>>  duplex auto
>>  speed auto
>>  pppoe enable group CISCO
>> end
>>
>> !
>> interface Virtual-Template16
>>  mtu 1492
>>  ip address 172.31.255.1 255.255.255.0
>>  ip ospf network point-to-multipoint
>>  ip ospf mtu-ignore
>>  peer default ip address pool 1.6
>>  ppp authentication chap
>> end
>>
>> usename R2 password pass
>>
>> ip local-pool 6.6 172.31.255.254
>>
>> __________________________________________________
>>
>> Client R2:
>> interface FastEthernet0/0
>>  no ip address
>>  ip ospf network point-to-multipoint
>>  ip ospf mtu-ignore
>>  speed auto
>>  half-duplex
>>  pppoe enable
>>  pppoe-client dial-pool-number 16
>> !
>>
>> interface Dialer16
>>  mtu 1492
>>  ip address negotiated
>>  encapsulation ppp
>>  ip ospf network point-to-multipoint
>>  dialer pool 16
>>  dialer idle-timeout 0
>>  dialer persistent
>>  no peer neighbor-route
>>  ppp chap password 0 pass
>> end
>>
>> R2:
>> sh ip ospf int br
>> Interface    PID   Area            IP Address/Mask    Cost  State Nbrs F/C
>> __________________________________________________________________________
>> Di16         1     2               172.31.255.254/32      1785  P2MP  0/0
>> __________________________________________________________________________
>>
>> Kind regards
>>
>> Tauseef
>> mobile: +44 7837209187
>>
>>
>> On 28 November 2012 10:10, Mohammad Mousa <mohd-mousa_at_hotmail.com> wrote:
>> Post your full configs so we can check together. Did you change the MTU?
>>
>> --
>> Mohammad Mousa
>> CCIE #36990
>>
>>
>>
>>
>>
>>
>> On Nov 28, 2012, at 12:28 PM, Tauseef Khan wrote:
>>
>> > Appreciate if some one could help. I have  ospf running on 2 routers R1
and
>> > R2.
>> > R2 is a PPPoE client and R1 is the server.  R2 has a negotiated ip
address
>> > on the dialer interface from R1 which is host (/32) address while R1 has
a
>> > /29 bit Ip address on its interface facing towards Client.
>> > OSPF adj is not coming up between the client and Server
>> > On client dialer int and Server int I have ip ospf network
>> > point-to-multipoint
>> > i also tried no peer neighbor-route on client dialer interface.
>> >
>> > debugs on the client side show:
>> > OSPF: Rcv pkt from 172.31.29.1, Dialer16, area 0.0.0.3 : src not on the
>> > same network
>> >
>> > I have tried changing the network type to poin-to-poitn as well but no
adj
>> >
>> > Regards
>> >
>> >
>> > Blogs and organic groups at http://www.ccie.net
>> >
>> > _______________________________________________________________________
>> > Subscription information may be found at:
>> > http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net