Re: troubleshoot - will I loose point ?

The marking script looks at things like the output of various show
commands, and the config. How would it know, or care, how you ended up
changing the config? You can put it in there however you like. Copy
and paste individual letters, use abbreviations or full commands, it's
all irrelevant.

You're marked on results, not how you get there. (As long as you don't
break restrictions, of course)

On 24/11/2012, at 7:46 AM, Imran Ali <immrccie_at_gmail.com> wrote:

> what a mind twisting question ! amazing one should i use a note pad or
> configure the router directly ..... :)-
>
> while using notepads is not prohibited and will not deducts any marks it
> deponds on situation .... for example if you only had to change neighbor
> ip address , then you might be wasting some time using notepads.
>
> while in some situations when have similar configs on multiple routers
> ..you can use notepad ... say DMVPN spokes has similar config except
> one or two commands
>
> you can copy paste after editing
>
> anohter example is hub and spoke frame relay
> On Fri, Nov 23, 2012 at 7:36 PM, Mohamed A. Abbas
> <m.abdelmonsef_at_gmail.com>wrote:
>
>> no copy paste them out but if the command is the same one u will put will
>> not be counted as a step
>> and i think its easier to modify it directly specially this question is
>> going for troubleshooting
>>
>> On Fri, Nov 23, 2012 at 1:21 PM, MSDP multicast
>> <multicast100_at_gmail.com>wrote:
>>
>>> Experts,
>>>>
>>>> Task: There is no neighborship between R1 to R3. Troubleshoot the
>> issue.
>>>>
>>>> Solution:
>>>> steps:
>>>> =>Copy and paste the whole BGP section config R1 and R2 config into the
>>>> notepad.
>>>> => Then modify the config in notepad and paste the "whole" config back
>>>> into the routers.
>>>>
>>>> Question:
>>>>
>>>> There may be one or two lines that might be missing in the BGP config
>> but
>>>> would I loose points if I copy and paste the whole section RTR to
>> notepad
>>>> to back onto the router?
>>>>
>>>> OR
>>>>
>>>> Shell I only modify the config that is relivent and not the whole BGP
>>>> section into noteapad and back onto the router?
>>>
>>>
>>> Blogs and organic groups at http://www.ccie.net
>>>
>>> _______________________________________________________________________
>>> Subscription information may be found at:
>>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>> --
>> *--*
>> **
>> *Eng. Mohamed A. Monsef*
>> *Cisco Networks Engineer*
>> *CCNP. - CCIP. - CCDP.*
>> CS-RSSS. - *IPv6-FGCE
>> .
>> *
>> ITIL. - *ISO/IEC 27002.*
>> ***Cell Phone : +2 0100 677 2 887*
>> * **+2 0109 255 6666**
>>
>> *
>> *
>> Land Line : +2 02 267 42 453
>>
>>
>> *
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Sat Nov 24 2012 - 08:56:52 ART