Re: Validate Update source command - RIP

Hello Nathan,

I did not configure no validate update source command on BB1.

I will try that. I was busy with my office work so did not get time to work
on it. I will do that.

Thank you all.

Mohammed Aftab

On Thu, Jun 7, 2012 at 9:58 AM, Nethan <nethandun_at_gmail.com> wrote:

> No I haven't. will try it and will post the results. :)
>
> Nethan
>
> On 6/7/2012 9:42 AM, Narbik Kocharians wrote:
>
> Have you tried running PPP on the link?
>
> On Wed, Jun 6, 2012 at 6:43 PM, Nethan <nethandun_at_gmail.com> wrote:
>
>> In this case how did you configure your static route. Does it points to
>> the nexthop ip or the outgoing interface?
>>
>> R1-----e0/0-------------------------------------------e0/1----BB1
>> 1.1.1.1/24
>> 2.2.2.2/24
>> In this scenario you need to use two static routes as below
>>
>> R1
>> ip route 2.2.2.2 255.255.255.255 e0/0
>>
>> BB1
>> ip route 1.1.1.1 255.255.255.255 e0/1
>>
>> not only the above, you need to configure no validate-update-source on
>> both R1 and BB1.
>>
>> Then you should receive all the rip routes from BB1 --> R1 and R1--->BB1.
>> So no matter how many routers connected to R1, they should be able to
>> reach BB1 connected interfaces if all are advertised by rip.
>>
>> Nethan
>>
>> On 6/6/2012 2:30 PM, Mohammed Aftab Memon wrote:
>>
>>> Hello All,
>>>
>>> I am stuck and need your help.
>>>
>>> BB1---connected to R1 and is configured with a different subnet. Both run
>>> Rip v2 but are not reachable. I did configure no validate source command
>>> and I was able to see all the routes from BB1 in R1 routing table. When I
>>> ping from R1 to those routes they were not reachable so I created a
>>> static
>>> route and I was able to reach those ips.
>>>
>>>
>>> Now in the network where R1 is connected to other routers, from those
>>> devices I am able to reach R1 ip address at the same time I do see all
>>> the
>>> routes in the routing table which come from BB1. But those IPs are not
>>> reachable. When I did a traceroute the packet goes till R1 but there is
>>> no
>>> response from there on.
>>>
>>> I am not sure what needs to be done and I am failing here.
>>>
>>> Please assist.
>>>
>>> Mohammed Aftab Memon
>>>
>>>
>>> Blogs and organic groups at http://www.ccie.net
>>>
>>> _______________________________________________________________________
>>> Subscription information may be found at:
>>> http://www.groupstudy.com/list/CCIELab.html
>>>
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>>
>>
>>
>>
>>
>
>
> --
> *Narbik Kocharians
> *CCSI#30832, CCIE# 12410 (R&S, SP, Security)
> *www.MicronicsTraining.com* <http://www.micronicstraining.com/>
> Sr. Technical Instructor
> YES! We take Cisco Learning Credits!
> A Cisco Learning Partner

Blogs and organic groups at http://www.ccie.net
Received on Tue Jun 12 2012 - 11:58:06 ART