Re: OER master active-probe

Problem was I didn't have an oer-map that matched the prefix. Any
active probe will need oer map....? please confirm or correct this
statement.

R6#sh run | b ^oer-map
oer-map prfx 10
 match traffic-class prefix-list prfx

R6#sh oer master active-probes
        OER Master Controller active-probes
Border = Border Router running this Probe
State = Un/Assigned to a Prefix
Prefix = Probe is assigned to this Prefix
Type = Probe Type
Target = Target Address
TPort = Target Port
How = Was the probe Learned or Configured
N - Not applicable

The following Probes exist:

State Prefix Type Target TPort How Codec
Assigned 3.3.3.3/32 echo 3.3.3.3 N Cfgd N

The following Probes are running:

Border State Prefix Type Target TPort
1.1.1.6 ACTIVE 3.3.3.3/32 echo 3.3.3.3 N

Thanks,
Marc

On Sun, Apr 22, 2012 at 1:16 PM, marc edwards <renorider_at_gmail.com> wrote:
> Experts,
>
> I am running through a lab on OER. When I look at the sh oer master
> active-probe output on my rack I see:
> ----
> R6#sh oer master active-probes
> OER Master Controller active-probes
> Border = Border Router running this Probe
> State = Un/Assigned to a Prefix
> Prefix = Probe is assigned to this Prefix
> Type = Probe Type
> Target = Target Address
> TPort = Target Port
> How = Was the probe Learned or Configured
> N - Not applicable
>
> The following Probes exist:
>
> State Prefix Type Target TPort How Codec
> Unassigned echo 3.3.3.3 N Cfgd N
>
> The following Probes are running:
>
> Border State Prefix Type Target TPort
> ----
> When I look at answer key it shows:
> ---
> OER Master Controller active-probes
> Border = Border Router running this Probe
> = Probe is assigned to this Prefix
> State = Un/Assigned to a Prefix
> Prefix
>
> Type = Probe Type
> Target = Target Address
> TPort = Target Port
> llowing Probes exist:
> tate Prefix
>
> S
> How = Was the probe Learned or Configured
> N - Not applicable
>
> The
> f
> o Type Target TPort How
> Assigned 3.3.3.3/32 echo 3.3.3.3 N Cfgd
> The following Probes are running:
>
> Border State Prefix Type Target TPo
> r1.1.1.6 ACTIVE 3.3.3.3/32 echo 3.3.3.3 N
> ----
>
> Any ideas why my state is unassigned? Here is configuration from router
>
>
> R6#sh run | b ^oer
>
> oer master
> policy-rules prfx
> logging
> !
> border 1.1.1.6 key-chain OER
> interface Serial0/0/0.62 external
> interface FastEthernet0/1 external
> interface FastEthernet0/0 internal
> !
> learn
> delay
> periodic-interval 3
> monitor-period 1
> no max range receive
> mode route control
> mode monitor active
> !
> active-probe echo 3.3.3.3
> !
> oer border
> logging
> local FastEthernet0/0
> master 1.1.1.6 key-chain OER
> !
> ip prefix-list prfx seq 5 permit 3.3.3.3/32

Blogs and organic groups at http://www.ccie.net
Received on Sun Apr 22 2012 - 13:57:19 ART