RE: xmodem or interface config command in very old rommon

Release Notes for 11.2 specifically calls out the 2509-RJ and 2511-RJ

http://www.cisco.com/en/US/products/sw/iosswrel/ps1824/prod_release_note0918
6a008007fba0.html

Note The Cisco AS2509-RJ and AS2511-RJ only support software images for
Cisco IOS Release 11.2(5)P or later.

David

--
http://dcp.dcptech.com
> -----Original Message-----
> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
> Atsuhiro Nakamura
> Sent: Tuesday, October 18, 2011 6:17 PM
> To: Michael Kiefer
> Cc: ccielab_at_groupstudy.com
> Subject: Re: xmodem or interface config command in very old rommon
> 
> Hi Michael,
> 
> Thank you for your prompt comment.
> 
> I have confirmed that the RxBoot worked and recognized hardware
> properly
> then successfully could upgrade IOS to c2500-is-l.112-18.bin via tftp (
> via Ethernet ).
> I also confirmed RxBoot could work fine as access server then we will
> keep using this software and configuration.
> 
> Now my question is, however, why those IOS image cannot recognize the
> hardware properly...?
> Do you have any ideas?
> 
> -------
> Router(boot)#sh ver
> Cisco Internetwork Operating System Software
> IOS (tm) 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c)XB1,
> PLATFORM SPECIFIC RELEASE SOFTWARE (fc1)
> Copyright (c) 1986-1996 by cisco Systems, Inc.
> Compiled Wed 10-Sep-97 13:06 by phester
> Image text-base: 0x01010000, data-base: 0x00001000
> 
> ROM: System Bootstrap, Version 11.0(10c)XB1, PLATFORM SPECIFIC RELEASE
> SOFTWARE (fc1)
> 
> Router uptime is 1 minute
> System restarted by reload
> Running default software
> 
> cisco AS2509-RJ (68030) processor (re
> %SYS-5-CONFIG_I: Configured from console by consolevision I) with
> 2048K/2048K bytes of memory.
> Processor board ID 08309343, with hardware revision 00000000
> X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
> 1 Ethernet/IEEE 802.3 interface.
> 1 Serial network interface.
> 8 terminal lines.
> 32K bytes of non-volatile configuration memory.
> 8192K bytes of processor board System flash (Read/Write)
> 
> Configuration register is 0x2101
> -------
> Router#show ver
> Cisco Internetwork Operating System Software
> IOS (tm) 2500 Software (C2500-IS-L), Version 11.2(18), RELEASE SOFTWARE
> (fc1)
> Copyright (c) 1986-1999 by cisco Systems, Inc.
> Compiled Mon 05-Apr-99 19:58 by jaturner
> Image text-base: 0x0302F3B0, data-base: 0x00001000
> 
> ROM: System Bootstrap, Version 11.0(10c)XB1, PLATFORM SPECIFIC RELEASE
> SOFTWARE (fc1)
> BOOTFLASH: 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c)XB1,
> PLATFORM SPECIFIC RELEASE SOFTWARE (fc1)
> 
> Router uptime is 0 minutes
> System restarted by reload
> System image file is "flash:c2500-is-l.112-18.bin", booted via flash
> 
> cisco 2500 (68030) processor (revision I) with 2048K/2048K bytes of
> memory.
> Processor board ID 08309343, with hardware revision 00000000
> Bridging software.
> X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
> 32K bytes of non-volatile configuration memory.
> 8192K bytes of processor board System flash (Read ONLY)
> 
> Configuration register is 0x2102
> -------
> 
> Best regards,
> 
> Achi
> 
> > Try this:
> >
> > RXBoot:
> >
> http://www.cisco.com/en/US/products/hw/routers/ps233/products_tech_note
> 09186a00800941aa.shtml
> >
> >
> >
> > On Mon, Oct 17, 2011 at 11:45 AM, NAKAMURA Atsuhiro
> > <a-naka_at_mtf.biglobe.ne.jp <mailto:a-naka_at_mtf.biglobe.ne.jp>> wrote:
> >
> >     Dear experts,
> >
> >     Does anybody has an idea,
> >
> >      - What is the xmodem file transfer command in very old rommon?
> >
> >     Or,
> >
> >      - How to configure IP address of Ethernet interface in very old
> >     rommon?
> >
> >     Now I have a classic 2509-RJ with IOS 11.2(16), but it doesn't
> >     recognize its interface properly.
> >     I guess the IOS image c2500-c-l_112-16 doesn't match the
> hardware.
> >     So I want to try IOS upgrade to c2500-is-l.112-18.bin.
> >
> >     -------
> >     Router#sh ver
> >     Cisco Internetwork Operating System Software
> >     IOS (tm) 2500 Software (C2500-C-L), Version 11.2(16), RELEASE
> >     SOFTWARE (fc1)
> >     Copyright (c) 1986-1998 by cisco Systems, Inc.
> >     Compiled Tue 06-Oct-98 11:59 by ashah
> >     Image text-base: 0x03023730, data-base: 0x00001000
> >
> >     ROM: System Bootstrap, Version 11.0(10c)XB1, PLATFORM SPECIFIC
> >     RELEASE SOFTWARE (fc1)
> >     BOOTFLASH: 3000 Bootstrap Software (IGS-BOOT-R), Version
> >     11.0(10c)XB1, PLATFORM SPECIFIC RELEASE SOFTWARE (fc1)
> >
> >     Router uptime is 44 minutes
> >     System restarted by reload at 09:29:15 SGT Fri Oct 14 2011
> >     System image file is "flash:c2500-c-l_112-16", booted via flash
> >
> >     cisco 2500 (68030) processor (revision I) with 2048K/2048K bytes
> >     of memory.
> >     Processor board ID 08309343, with hardware revision 00000000
> >     Bridging software.
> >     SuperLAT software copyright 1990 by Meridian Technology Corp).
> >     TN3270 Emulation software.
> >     X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
> >     32K bytes of non-volatile configuration memory.
> >     8192K bytes of processor board System flash (Read ONLY)
> >
> >     Configuration register is 0x2102
> >
> >     -------
> >     >?
> >     $            Toggle cache state
> >     B [filename] [TFTP Server IP address | TFTP Server Name]
> >                 Load and execute system image from ROM or from TFTP
> server
> >     C [address]  Continue execution [optional address]
> >     D /S M L V   Deposit value V of size S into location L with
> modifier M
> >     E /S M L     Examine location L with size S with modifier M
> >     G [address]  Begin execution
> >     H            Help for commands
> >     I            Initialize
> >     K            Stack trace
> >     L [filename] [TFTP Server IP address | TFTP Server Name]
> >                 Load system image from ROM or from TFTP server, but
> do not
> >                 begin execution
> >     O            Show configuration register option settings
> >     P            Set the break point
> >     S            Single step next instruction
> >     T function   Test device (? for help)
> >
> >     Deposit and Examine sizes may be B (byte), L (long) or S (short).
> >     Modifiers may be R (register) or S (byte swap).
> >     Register names are: D0-D7, A0-A6, SS, US, SR, and PC
> >     >
> >     -------
> >
> >     Best regards,
> >
> >     Achi
> >
> >
> >     Blogs and organic groups at http://www.ccie.net
> >
> >
> _______________________________________________________________________
> >     Subscription information may be found at:
> >     http://www.groupstudy.com/list/CCIELab.html
> 
> 
> Blogs and organic groups at http://www.ccie.net
> 
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net