Re: 2511 ACCESS SERVER

It's not ctl-x.
It's control caret, followed by x.
Please try this first by telneting to something else and manage to
get back to the router.

What other hardware do you have ? You sure have a serial terminal
emulator, or else you would not be able to configure the 2511, right ?
You have a switch so you can access the 2511 via network ?

Do you have RJ45s or DB25 ? Do you have adapters ? (RJ to DB)

-Carlos

ACHAL GUPTA @ 16/06/2011 10:00 -0300 dixit:
> ya i did that pressing (ctrl x).its not working
>
> i attached only one octal cable at 1-8 lines port in 2511 access server
> and attach only 1 and 2 to R1 & R2 to test.
>
> and i took console of 2511 and trying all that config.....
>
> Please tell me what to do...?
>
> thanks
> Achal
>
> On Thu, Jun 16, 2011 at 9:51 PM, Carlos G Mendioroz <tron_at_huapi.ba.ar
> <mailto:tron_at_huapi.ba.ar>> wrote:
>
> Achal,
> it's not "hanging", it's connected.
> You can tell by entereing the escape sequence (ctl-^ x) and you
> should get the router prompt again.
>
> The 2511 has 2 octal cables, one for 1-8 and the other for 9-16.
> They might have RJ-45 or DB25. They should be labeled 1 to 8.
>
> Is the other end connected to something ? You can try to connect
> to a com port and see if your link is working each way.
> You will not see echo! May be some port is fried, so test each
> one and single the working ones, if that's the case.
>
> -Carlos
>
> ACHAL GUPTA @ 16/06/2011 08:37 -0300 dixit:
>
> thanks for reply....
>
> My line numbers are 1 to 16 and i think its ok
>
> Cisco2511#sh line
> Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise
> Overruns
> Int
> * 0 CTY - - - - - 0 1
> 0/0
> -
> 1 TTY 9600/9600 - - - - - 0 0
> 0/0
> -
> 2 TTY 9600/9600 - - - - - 0 0
> 0/0
> -
> 3 TTY 9600/9600 - - - - - 0 0
> 0/0
> -
> 4 TTY 9600/9600 - - - - - 0 0
> 0/0
> -
> 5 TTY 9600/9600 - - - - - 0 0
> 0/0
> -
> 6 TTY 9600/9600 - - - - - 0 0
> 0/0
> -
> 7 TTY 9600/9600 - - - - - 0 0
> 0/0
> -
> 8 TTY 9600/9600 - - - - - 0 0
> 0/0
> -
> 9 TTY 9600/9600 - - - - - 0 0
> 0/0
> -
> 10 TTY 9600/9600 - - - - - 0 0
> 0/0
> -
> 11 TTY 9600/9600 - - - - - 0 0
> 0/0
> -
> 12 TTY 9600/9600 - - - - - 0 0
> 0/0
> -
> 13 TTY 9600/9600 - - - - - 0 0
> 0/0
> -
> 14 TTY 9600/9600 - - - - - 0 0
> 0/0
> -
> 15 TTY 9600/9600 - - - - - 0 0
> 0/0
> -
> 16 TTY 9600/9600 - - - - - 0 0
> 0/0
> -
> 17 AUX 9600/9600 - - - - - 0 0
> 0/0
> -
> 18 VTY - - - - - 0 0
> 0/0
> -
> 19 VTY - - - - - 0 0
> 0/0
> -
> 20 VTY - - - - - 0 0
> 0/0
> -
>
> and i am trying telnet r1 and straight away r1 also but it shows
> the
> following and hang i restart my router and then it comes normal
>
>
> Cisco2511#telnet r1
> Trying R1 (1.1.1.1, 2002)... Open
>
>
> i dont know why it hang.... pls tell me whats wrong m i doing...?
>
> thanks
> Achal
> On Thu, Jun 16, 2011 at 8:06 PM, Carlos G Mendioroz
> <tron_at_huapi.ba.ar <mailto:tron_at_huapi.ba.ar>>wrote:
>
> ACHAL,
> your config is ok as long as your lines are numbered 1 to 16,
> which in the case of a 2511 they should. Do a show line to
> verify.
>
> What exactly is your problem ? Can you telnet to the reverse
> telnet port
> and get connected ? Or refused ?
> Connected and nothing ?
>
> -Carlos
>
>
> ACHAL GUPTA @ 15/06/2011 20:08 -0300 dixit:
>
> Hello Experts,
>
> Can anyone tell me how can i make my 2511 roter as a
> access server?
>
> i tried with following config but not working.
>
> I gave the ip address to ethernet (172.16.1.2) and its
> pinging my Laptop
> ip
> address.
>
> i attach my octal cable also with no.1 cable in R1 and
> no.2 cable in
> R2.........
>
> ip host R1 2001 172.16.1.2
> ip host R2 2002 172.16.1.2
> - - - - - -
> - - - - - -
>
> line con 0
> line 1 16
> exec-timeout 0 0
> no exec
> transport input all
> line vty 0 4
> password cisco
> login
>
>
> i did that config but it is not working
>
> pls tell me ehat i m doing wrong and what else i will
> have to do?
>
>
> --
> Carlos G Mendioroz <tron_at_huapi.ba.ar
> <mailto:tron_at_huapi.ba.ar>> LW7 EQI Argentina
>
>
>
>
>
> --
> Carlos G Mendioroz <tron_at_huapi.ba.ar <mailto:tron_at_huapi.ba.ar>>
> LW7 EQI Argentina
>
>
>
>
> --
> *
> *
> *
> *
> *
> Thanks,*
> *Achal*
>

-- 
Carlos G Mendioroz  <tron_at_huapi.ba.ar>  LW7 EQI  Argentina
Blogs and organic groups at http://www.ccie.net