Re: 2511 ACCESS SERVER

Achal,
it's not "hanging", it's connected.
You can tell by entereing the escape sequence (ctl-^ x) and you
should get the router prompt again.

The 2511 has 2 octal cables, one for 1-8 and the other for 9-16.
They might have RJ-45 or DB25. They should be labeled 1 to 8.

Is the other end connected to something ? You can try to connect
to a com port and see if your link is working each way.
You will not see echo! May be some port is fried, so test each
one and single the working ones, if that's the case.

-Carlos

ACHAL GUPTA @ 16/06/2011 08:37 -0300 dixit:
> thanks for reply....
>
> My line numbers are 1 to 16 and i think its ok
>
> Cisco2511#sh line
> Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns
> Int
> * 0 CTY - - - - - 0 1 0/0
> -
> 1 TTY 9600/9600 - - - - - 0 0 0/0
> -
> 2 TTY 9600/9600 - - - - - 0 0 0/0
> -
> 3 TTY 9600/9600 - - - - - 0 0 0/0
> -
> 4 TTY 9600/9600 - - - - - 0 0 0/0
> -
> 5 TTY 9600/9600 - - - - - 0 0 0/0
> -
> 6 TTY 9600/9600 - - - - - 0 0 0/0
> -
> 7 TTY 9600/9600 - - - - - 0 0 0/0
> -
> 8 TTY 9600/9600 - - - - - 0 0 0/0
> -
> 9 TTY 9600/9600 - - - - - 0 0 0/0
> -
> 10 TTY 9600/9600 - - - - - 0 0 0/0
> -
> 11 TTY 9600/9600 - - - - - 0 0 0/0
> -
> 12 TTY 9600/9600 - - - - - 0 0 0/0
> -
> 13 TTY 9600/9600 - - - - - 0 0 0/0
> -
> 14 TTY 9600/9600 - - - - - 0 0 0/0
> -
> 15 TTY 9600/9600 - - - - - 0 0 0/0
> -
> 16 TTY 9600/9600 - - - - - 0 0 0/0
> -
> 17 AUX 9600/9600 - - - - - 0 0 0/0
> -
> 18 VTY - - - - - 0 0 0/0
> -
> 19 VTY - - - - - 0 0 0/0
> -
> 20 VTY - - - - - 0 0 0/0
> -
>
> and i am trying telnet r1 and straight away r1 also but it shows the
> following and hang i restart my router and then it comes normal
>
>
> Cisco2511#telnet r1
> Trying R1 (1.1.1.1, 2002)... Open
>
>
> i dont know why it hang.... pls tell me whats wrong m i doing...?
>
> thanks
> Achal
> On Thu, Jun 16, 2011 at 8:06 PM, Carlos G Mendioroz <tron_at_huapi.ba.ar>wrote:
>
>> ACHAL,
>> your config is ok as long as your lines are numbered 1 to 16,
>> which in the case of a 2511 they should. Do a show line to verify.
>>
>> What exactly is your problem ? Can you telnet to the reverse telnet port
>> and get connected ? Or refused ?
>> Connected and nothing ?
>>
>> -Carlos
>>
>>
>> ACHAL GUPTA @ 15/06/2011 20:08 -0300 dixit:
>>
>> Hello Experts,
>>> Can anyone tell me how can i make my 2511 roter as a access server?
>>>
>>> i tried with following config but not working.
>>>
>>> I gave the ip address to ethernet (172.16.1.2) and its pinging my Laptop
>>> ip
>>> address.
>>>
>>> i attach my octal cable also with no.1 cable in R1 and no.2 cable in
>>> R2.........
>>>
>>> ip host R1 2001 172.16.1.2
>>> ip host R2 2002 172.16.1.2
>>> - - - - - -
>>> - - - - - -
>>>
>>> line con 0
>>> line 1 16
>>> exec-timeout 0 0
>>> no exec
>>> transport input all
>>> line vty 0 4
>>> password cisco
>>> login
>>>
>>>
>>> i did that config but it is not working
>>>
>>> pls tell me ehat i m doing wrong and what else i will have to do?
>>>
>>>
>> --
>> Carlos G Mendioroz <tron_at_huapi.ba.ar> LW7 EQI Argentina
>>
>
>
>

-- 
Carlos G Mendioroz  <tron_at_huapi.ba.ar>  LW7 EQI  Argentina
Blogs and organic groups at http://www.ccie.net