Re: Frame Switch Issue

Forget FR .....
just default the configs and see things work fine in default configs
(default encap HDLC) .. and under what clock rate ..
remember diff clock rates are supported by diff. cable types..

yours is a V.35 cable .. so till 8 mbps clock is fine ..

just do default and let us know results ..

Then we will proceed to FR part /

2) From show controller ; i see that u r using DTE end of cable at FR switch
. You are supposed to use a DCE end at FR switch (this is a mandate as this
end will supply clocking ) . Please do that as well and let us know results
.

Thanks
Gaurav Madan
CCIE

On Thu, May 19, 2011 at 11:18 PM, Dennis Worth <dennis.worth_at_gmail.com>wrote:

> I think it's just what come up after default interface though.
>
>
> On Thu, May 19, 2011 at 12:16 PM, Dennis Worth <dennis.worth_at_gmail.com
> >wrote:
>
> > Found this is after logging.
> >
> > *May 19 18:05:52.419: %LINK-5-CHANGED: Interface Serial1/0, changed state
> > to administratively down
> > *May 19 18:06:02.791: %LINK-3-UPDOWN: Interface Serial1/0, changed state
> to
> > down
> > *May 19 18:11:25.271: %LINK-3-BOGUSENCAP: Interface Serial1/0, bad
> > encapsulation in idb->enctype = 0x0
> > *May 19 18:11:33.351: %LINK-3-BOGUSENCAP: Interface Serial1/0, bad
> > encapsulation in idb->enctype = 0x0
> > *May 19 18:11:36.851: %LINK-3-UPDOWN: Interface Serial1/0, changed state
> to
> > down
> > *May 19 18:12:08.155: %LINK-3-BOGUSENCAP: Interface Serial1/0, bad
> > encapsulation in idb->enctype = 0x0
> >
> > On Thu, May 19, 2011 at 12:05 PM, Narbik Kocharians <narbikk_at_gmail.com
> >wrote:
> >
> >> Did you enable "Frame-relay Switching"?
> >>
> >>
> >> On Thu, May 19, 2011 at 12:04 PM, Narbik Kocharians <narbikk_at_gmail.com
> >wrote:
> >>
> >>> S0/0/0 is missing the clock rate.
> >>>
> >>>
> >>> On Thu, May 19, 2011 at 11:57 AM, Dennis Worth <dennis.worth_at_gmail.com
> >wrote:
> >>>
> >>>> Group,
> >>>>
> >>>> Ran into an issue with NM A/S card. It shows up, but all interfaces
> >>>> state
> >>>> down/down. Am I missing something obvious?
> >>>>
> >>>> interface Serial0/0/0
> >>>> description R1
> >>>> no ip address
> >>>> encapsulation frame-relay
> >>>> no fair-queue
> >>>> frame-relay intf-type dce
> >>>> frame-relay route 102 interface Serial0/1/0 201
> >>>> frame-relay route 103 interface Serial1/0 301
> >>>> frame-relay route 104 interface Serial1/1 401
> >>>> frame-relay route 105 interface Serial1/2 501
> >>>> frame-relay route 106 interface Serial1/3 601
> >>>> frame-relay route 112 interface Serial0/1/0 211
> >>>> !
> >>>> interface Serial0/1/0
> >>>> description R2
> >>>> no ip address
> >>>> encapsulation frame-relay
> >>>> no fair-queue
> >>>> clock rate 2000000
> >>>> frame-relay intf-type dce
> >>>> frame-relay route 201 interface Serial0/0/0 102
> >>>> frame-relay route 202 interface Serial0/2/0 302
> >>>> frame-relay route 204 interface Serial1/0 402
> >>>> frame-relay route 205 interface Serial1/1 502
> >>>> frame-relay route 206 interface Serial1/2 602
> >>>> !
> >>>> interface Serial0/2/0
> >>>> description R3
> >>>> no ip address
> >>>> encapsulation frame-relay
> >>>> no fair-queue
> >>>> clock rate 2000000
> >>>> frame-relay intf-type dce
> >>>> frame-relay route 301 interface Serial0/0/0 102
> >>>> frame-relay route 302 interface Serial0/1/0 203
> >>>> frame-relay route 304 interface Serial1/0 403
> >>>> frame-relay route 305 interface Serial1/1 503
> >>>> frame-relay route 306 interface Serial1/2 603
> >>>> !
> >>>> interface Serial1/0
> >>>> description R4
> >>>> no ip address
> >>>> encapsulation frame-relay
> >>>> no fair-queue
> >>>> clock rate 64000
> >>>> dce-terminal-timing-enable
> >>>> frame-relay intf-type dce
> >>>> frame-relay route 401 interface Serial0/0/0 104
> >>>> frame-relay route 402 interface Serial0/1/0 204
> >>>> frame-relay route 403 interface Serial0/2/0 304
> >>>> frame-relay route 405 interface Serial1/1 504
> >>>> frame-relay route 406 interface Serial1/2 604
> >>>> !
> >>>> interface Serial1/1
> >>>> description R5
> >>>> no ip address
> >>>> encapsulation frame-relay
> >>>> no fair-queue
> >>>> clock rate 128000
> >>>> no dce-terminal-timing-enable
> >>>> frame-relay intf-type dce
> >>>> frame-relay route 501 interface Serial0/0/0 105
> >>>> frame-relay route 502 interface Serial0/1/0 205
> >>>> frame-relay route 503 interface Serial0/2/0 305
> >>>> frame-relay route 504 interface Serial1/0 405
> >>>> frame-relay route 506 interface Serial1/2 605
> >>>> !
> >>>> interface Serial1/2
> >>>> description R6
> >>>> no ip address
> >>>> encapsulation frame-relay
> >>>> no fair-queue
> >>>> clock rate 128000
> >>>> no dce-terminal-timing-enable
> >>>> frame-relay intf-type dce
> >>>> frame-relay route 601 interface Serial0/0/0 106
> >>>> frame-relay route 602 interface Serial0/1/0 206
> >>>> frame-relay route 603 interface Serial0/2/0 306
> >>>> frame-relay route 604 interface Serial1/0 406
> >>>> frame-relay route 605 interface Serial1/1 506
> >>>>
> >>>> Interface IP-Address OK? Method Status
> >>>> Protocol
> >>>> GigabitEthernet0/0 unassigned YES NVRAM administratively
> >>>> down
> >>>> down
> >>>> GigabitEthernet0/1 unassigned YES NVRAM administratively
> >>>> down
> >>>> down
> >>>> Serial0/0/0 unassigned YES NVRAM up
> >>>> up
> >>>> Serial0/1/0 unassigned YES NVRAM up
> >>>> up
> >>>> Serial0/2/0 unassigned YES NVRAM up
> >>>> up
> >>>> Serial1/0 unassigned YES manual down
> >>>> down
> >>>> Serial1/1 unassigned YES NVRAM down
> >>>> down
> >>>> Serial1/2 unassigned YES NVRAM down
> >>>> down
> >>>> Serial1/3 unassigned YES NVRAM down
> >>>> down
> >>>>
> >>>> ~~~~~~~~~~Does Not Work~~~~~~~~~~
> >>>> FRS#sh controllers serial1/0
> >>>> CD2430 Slot 1, Port 0, Controller 0, Channel 0, Revision 19
> >>>> Channel mode is synchronous serial
> >>>> idb 0x468CA034, buffer size 1524, V.35 DCE cable, clockrate 64000
> >>>>
> >>>>
> >>>> Serial1/0 is down, line protocol is down
> >>>> Hardware is CD2430 in sync mode
> >>>> Description: R4
> >>>> MTU 1500 bytes, BW 128 Kbit, DLY 20000 usec,
> >>>> reliability 255/255, txload 1/255, rxload 1/255
> >>>> Encapsulation FRAME-RELAY, loopback not set
> >>>> Keepalive set (10 sec)
> >>>> LMI enq sent 0, LMI stat recvd 0, LMI upd recvd 0
> >>>> LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0, DCE LMI down
> >>>> LMI DLCI 1023 LMI type is CISCO frame relay DCE
> >>>> FR SVC disabled, LAPF state down
> >>>> Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface
> broadcasts
> >>>> 0
> >>>> Last input never, output never, output hang never
> >>>> Last clearing of "show interface" counters 00:17:34
> >>>> Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
> >>>> Queueing strategy: fifo
> >>>> Output queue: 0/40 (size/max)
> >>>> 5 minute input rate 0 bits/sec, 0 packets/sec
> >>>> 5 minute output rate 0 bits/sec, 0 packets/sec
> >>>> 0 packets input, 0 bytes, 0 no buffer
> >>>> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> >>>> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
> >>>> 0 packets output, 0 bytes, 0 underruns
> >>>> 0 output errors, 0 collisions, 35 interface resets
> >>>> 0 output buffer failures, 0 output buffers swapped out
> >>>> 0 carrier transitions
> >>>> DCD=up DSR=up DTR=down RTS=down CTS=up
> >>>>
> >>>>
> >>>> ~~~~~~~~~~WORKS~~~~~~~~~~~~~~~~
> >>>> FRS#sh controllers serial0/0/0
> >>>> Interface Serial0/0/0
> >>>> Hardware is GT96K
> >>>> DTE V.35idb at 0x468AAC78, driver data structure at 0x468B23AC
> >>>> wic_info 0x468B29C0
> >>>> Physical Port 1, SCC Num 1
> >>>>
> >>>> Serial0/0/0 is up, line protocol is up
> >>>> Hardware is GT96K Serial
> >>>> Description: R1
> >>>> MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
> >>>> reliability 255/255, txload 1/255, rxload 1/255
> >>>> Encapsulation FRAME-RELAY, loopback not set
> >>>> Keepalive set (10 sec)
> >>>> LMI enq sent 0, LMI stat recvd 0, LMI upd recvd 0
> >>>> LMI enq recvd 218, LMI stat sent 218, LMI upd sent 0, DCE LMI up
> >>>> LMI DLCI 1023 LMI type is CISCO frame relay DCE
> >>>> FR SVC disabled, LAPF state down
> >>>> Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface
> broadcasts
> >>>> 0
> >>>> Last input 00:00:08, output 00:00:08, output hang never
> >>>> Last clearing of "show interface" counters 00:36:22
> >>>> Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
> >>>> Queueing strategy: fifo
> >>>> Output queue: 0/40 (size/max)
> >>>> 5 minute input rate 0 bits/sec, 0 packets/sec
> >>>> 5 minute output rate 0 bits/sec, 0 packets/sec
> >>>> 218 packets input, 2834 bytes, 0 no buffer
> >>>> Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
> >>>> 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
> >>>> 218 packets output, 4658 bytes, 0 underruns
> >>>> 0 output errors, 0 collisions, 1 interface resets
> >>>> 0 output buffer failures, 0 output buffers swapped out
> >>>> 0 carrier transitions
> >>>> DCD=up DSR=up DTR=up RTS=up CTS=up
> >>>>
> >>>> Thanks,
> >>>>
> >>>> --
> >>>> Dennis Worth
> >>>>
> >>>> "Of all men's miseries the bitterest it this: to know so much and to
> >>>> have
> >>>> control over nothing."
> >>>> --Herodotus
> >>>>
> >>>>
> >>>> Blogs and organic groups at http://www.ccie.net
> >>>>
> >>>>
> _______________________________________________________________________
> >>>> Subscription information may be found at:
> >>>> http://www.groupstudy.com/list/CCIELab.html
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>
> >>>
> >>> --
> >>> *Narbik Kocharians
> >>> *CCSI#30832, CCIE# 12410 (R&S, SP, Security)
> >>> www.MicronicsTraining.com <http://www.micronicstraining.com/>
> >>> Sr. Technical Instructor
> >>> *Ask about our FREE Lab Voucher with our Boot Camps*
> >>> YES! We take Cisco Learning Credits!
> >>> Training & Remote Racks available
> >>>
> >>>
> >>
> >>
> >> --
> >> *Narbik Kocharians
> >> *CCSI#30832, CCIE# 12410 (R&S, SP, Security)
> >> www.MicronicsTraining.com <http://www.micronicstraining.com/>
> >> Sr. Technical Instructor
> >> *Ask about our FREE Lab Voucher with our Boot Camps*
> >> YES! We take Cisco Learning Credits!
> >> Training & Remote Racks available
> >>
> >>
> >
> >
> > --
> > Dennis Worth
> >
> > "Of all men's miseries the bitterest it this: to know so much and to have
> > control over nothing."
> > --Herodotus
> >
> >
>
>
> --
> Dennis Worth
>
> "Of all men's miseries the bitterest it this: to know so much and to have
> control over nothing."
> --Herodotus
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Fri May 20 2011 - 00:57:12 ART