Cisco 7941(SCCP) dialing out only signle digit

---------- Forwarded message ----------
From: Asim Riaz <ariaz78_at_gmail.com>
Date: Tue, Dec 21, 2010 at 6:33 PM
Subject: Re: Cisco 7941(SCCP) dialing out only signle digit
To: Carl Gosselin <carl.gosselin_at_altizone.com>

Hi Carl, you are right, found my mistake, there was a voip dial-peer with .+
:) and CME was matching that plan.
means that sip phone registered to CM behave diffrently because sip phone
was able to dial complete number not just one digit.

Thanks,

Asim

On Tue, Dec 21, 2010 at 3:24 PM, Carl Gosselin
<carl.gosselin_at_altizone.com>wrote:

> If the CME tries to connect on just 3 it means that you have a match in the
> dialplan for that CME.
>
> Run the "sh dial-peer voice sum" and look in the DEST-PATTERN colum if you
> don't see a pattern that is "3"
>
> You can also look at "sh ephone-dn sum" to see if there is not a "3"
> configured as an extension on a phone
>
> /Carl
>
>
> On Tue, Dec 21, 2010 at 10:10 AM, Asim Riaz <ariaz78_at_gmail.com> wrote:
>
>> i ran the debug command and looks like phone is only dialing 3 even i
>> dialed
>> 3006, i dont know what is wrong but looks like digit timeout or something,
>> any idea ?
>>
>>
>> ec 21 15:18:19.383: //498/5FFA1D83809D/CCAPI/cc_api_display_ie_subfields:
>> ccCallSetupRequest:
>> cisco-username=
>> ----- ccCallInfo IE subfields -----
>> cisco-ani=3005
>> cisco-anitype=0
>> cisco-aniplan=0
>> cisco-anipi=0
>> cisco-anisi=0
>> dest=3
>> cisco-desttype=0
>> cisco-destplan=0
>> cisco-rdie=FFFFFFFF
>> cisco-rdn=
>> cisco-lastrdn=
>> cisco-rdntype=0
>> cisco-rdnplan=0
>> cisco-rdnpi=0
>> cisco-rdnsi=0
>> cisco-redirectreason=0 fwd_final_type =0
>> final_redirectNumber =
>> hunt_group_timeout =0
>>
>> *Dec 21 15:18:19.383:
>> //498/5FFA1D83809D/CCAPI/ccIFCallSetupRequestPrivate:
>> Interface=0x662F1B1C, Interface Type=3, Destination=, Mode=0x0,
>> Call Params(Calling Number=3005,(Calling Name=3005)(TON=Unknown,
>> NPI=Unknown, Screening=Not Screened, Presentation=Allowed),
>> Called Number=3(TON=Unknown, NPI=Unknown), Calling Translated=FALSE
>> Thanks,
>>
>> Asim
>>
>> On Tue, Dec 21, 2010 at 1:52 PM, Ryan West <rwest_at_zyedge.com> wrote:
>>
>> > If you think your dial peers are configured correctly, try deb voip
>> ccapi
>> > inout. Either way, it will show which dial peer is being matched.
>> >
>> > Sent from handheld
>> >
>> > On Dec 21, 2010, at 8:37 AM, Mohammed Aftab Memon <
>> aftabmemon12_at_gmail.com>
>> > wrote:
>> > t
>> > > Check for that extension under Route Plan Report.
>> > >
>> > > It might give you the list if something is configured. Might be there
>> is
>> > > some pattern designed for this.
>> > >
>> > >
>> > >
>> > >
>> > > On Tue, Dec 21, 2010 at 6:37 PM, Asim Riaz <ariaz78_at_gmail.com> wrote:
>> > >
>> > >> Hi All,
>> > >> I have phone registed with CME but when i dial out from phone its
>> just
>> > dial
>> > >> only signle digit, means if i am dialing to another extention wich is
>> > 3006
>> > >> it dials only 3 , any idea ?
>> > >>
>> > >> Thanks in advance
>> > >>
>> > >> Asim
>> > >>
>> > >>
>> > >> Blogs and organic groups at http://www.ccie.net
>> > >>
>> > >>
>> _______________________________________________________________________
>> > >> Subscription information may be found at:
>> > >> http://www.groupstudy.com/list/CCIELab.html
>> > >
>> > >
>> > > Blogs and organic groups at http://www.ccie.net
>> > >
>> > >
>> _______________________________________________________________________
>> > > Subscription information may be found at:
>> > > http://www.groupstudy.com/list/CCIELab.html
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Tue Dec 21 2010 - 18:34:05 ART