Re: OT: HWIC-3G-GSM Module Configration Problem...need help

I am not sure if you've already done this but take the SIM card out from the
cellular module and put it in your SmartPhone - Sort out the activation
isssue first. Make sure data is activated on that SIM.

Then play it once above is confirmed.

On Sat, Oct 30, 2010 at 11:56 PM, muhammad adnan <taurusadnan19_at_gmail.com>wrote:

> Dear Bilal
> Router#show cellular 0/1/0 all
> Hardware Information
> ====================
> Modem Firmware Version = H1_1_9_3MCAP C:/WS/
> Modem Firmware built = 12/12/07
> Hardware Version = 1.0
> International Mobile Subscriber Identity (IMSI) = 606010105114370
> International Mobile Equipment Identity (IMEI) = 011359000487907
> Factory Serial Number (FSN) = D28026013381043
> Modem Status = Online
> Current Modem Temperature = 26 deg C, State = Normal
>
> Profile Information
> ====================
> Profile 1 = INACTIVE*
> --------
> PDP Type = IPv4
> Access Point Name (APN) = almadar.net
> Authentication = None
> Username: , Password:
>
> * - Default profile
>
> Data Connection Information
> ===========================
> Data Transmitted = 0 bytes, Received = 0 bytes
> Profile 1, Packet Session Status = INACTIVE
> Inactivity Reason = Normal inactivate state
> Profile 2, Packet Session Status = INACTIVE
> Inactivity Reason = Normal inactivate state
> Profile 3, Packet Session Status = INACTIVE
> Inactivity Reason = Normal inactivate state
> Profile 4, Packet Session Status = INACTIVE
> Inactivity Reason = Normal inactivate state
> Profile 5, Packet Session Status = INACTIVE
> Inactivity Reason = Normal inactivate state
> Profile 6, Packet Session Status = INACTIVE
> Inactivity Reason = Normal inactivate state
> Profile 7, Packet Session Status = INACTIVE
> Inactivity Reason = Normal inactivate state
> Profile 8, Packet Session Status = INACTIVE
> Inactivity Reason = Normal inactivate state
> Profile 9, Packet Session Status = INACTIVE
> Inactivity Reason = Normal inactivate state
> Profile 10, Packet Session Status = INACTIVE
> Inactivity Reason = Normal inactivate state
> Profile 11, Packet Session Status = INACTIVE
> Inactivity Reason = Normal inactivate state
> Profile 12, Packet Session Status = INACTIVE
> Inactivity Reason = Normal inactivate state
> Profile 13, Packet Session Status = INACTIVE
> Inactivity Reason = Normal inactivate state
> Profile 14, Packet Session Status = INACTIVE
> Inactivity Reason = Normal inactivate state
> Profile 15, Packet Session Status = INACTIVE
> Inactivity Reason = Normal inactivate state
> Profile 16, Packet Session Status = INACTIVE
> Inactivity Reason = Normal inactivate state
>
> Network Information
> ===================
> Current Service Status = Normal, Service Error = None
> Current Service = Combined
> Packet Service = GPRS (Attached)
> Packet Session Status = Inactive
> Current Roaming Status = Home
> Network Selection Mode = Automatic
> Country = 606, Network = 606 01
> Mobile Country Code (MCC) = 606
> Mobile Network Code (MNC) = 1
> Location Area Code (LAC) = 1
> Routing Area Code (RAC) = 1
> Cell ID = 11071
> Primary Scrambling Code = 0
> PLMN Selection = Automatic
> Registered PLMN = Libya Al Madar , Abbreviated = 606 01
> Service Provider = 606 01
>
> Radio Information
> =================
> Current Band = GSM 900, Channel Number = 5
> Current RSSI = -62 dBm
> Band Selected = Auto
>
> Modem Security Information
> ==========================
> Card Holder Verification (CHV1) = Disabled
> SIM Status = OK
> SIM User Operation Required = None
> Number of Retries remaining = 3
>
>
> Thanks
>
>
>
>
> On Sat, Oct 30, 2010 at 2:42 PM, Bilal Hansrod <bilal.hansrod_at_gmail.com
> >wrote:
>
> > Can you please send the output of *sh cell 0/1/0 all*
> >
> >
> > Bilal
> >
> >
> > On Sat, Oct 30, 2010 at 11:36 PM, muhammad adnan <
> taurusadnan19_at_gmail.com>wrote:
> >
> >> Dear Bilal i configure according to the Cisco Documentation
> >> and in my mail i pasted show run config...
> >>
> >>
> >>
> >>
> http://www.cisco.com/en/US/docs/routers/access/1800/1861/software/feature/guide/mrwlsgsm.html#wp1040391
> >>
> >> in my mail i ask that username and password is blank to access the
> >> internet
> >> Service provider ask me no authentication username and password blank
> ("i
> >> just put Apn in my phone and username and password blank and it works
> fine
> >> accessing the internet")
> >>
> >> if u need any more information kindly let me know again..
> >>
> >> Thanks
> >> Muhammad Adnan
> >>
> >>
> >>
> >> On Sat, Oct 30, 2010 at 2:28 PM, Bilal Hansrod <bilal.hansrod_at_gmail.com
> >wrote:
> >>
> >>> Hi Muhammad,
> >>>
> >>> I can't see a logical interface created for cell interface where you
> >>> define your PPP username/password and also the authentication method.
> >>>
> >>> An example from my config as below:
> >>>
> >>>
> >>> interface Dialer1
> >>> ip address negotiated
> >>> ip virtual-reassembly
> >>> encapsulation ppp
> >>> dialer pool 1
> >>> dialer idle-timeout 0
> >>> dialer string gsm
> >>> dialer persistent
> >>> dialer-group 1
> >>> no cdp enable
> >>> ppp authentication chap callin
> >>> ppp chap hostname XXX
> >>> ppp chap password YYY
> >>>
> >>>
> >>> Regards,
> >>>
> >>> Bilal
> >>>
> >>>
> >>> On Sat, Oct 30, 2010 at 11:05 PM, muhammad adnan <
> >>> taurusadnan19_at_gmail.com> wrote:
> >>>
> >>>> Dear Group members:-
> >>>> i am trying to configure the
> 3G-module.i
> >>>> have inserted my sim card into the HWIC module sim card properly
> >>>> working in
> >>>> the phone and i am accessing the internet.
> >>>> but when i configure HWIC module accordingly i am unable to access the
> >>>> internet my configration pasted below if any experience person guid me
> >>>> little.
> >>>>
> >>>>
> >>>> in my phone i just put APN and it work fine without Authentication
> >>>> *Service
> >>>> provider ask me* that the *username and password is blank..*
> >>>>
> >>>> country Libya
> >>>> GSM service provider =Almadar
> >>>> APN or access point name =almadar.net
> >>>>
> >>>>
> >>>>
> >>>>
> >>>> *Router#show cellular 0/1/0 profile
> >>>> Profile 1 = INACTIVE*
> >>>> --------
> >>>> PDP Type = IPv4
> >>>> Access Point Name (APN) = almadar.net
> >>>> Authentication = None
> >>>> Username: , Password:
> >>>>
> >>>> * - Default profile
> >>>> *
> >>>>
> >>>>
> --------------------------------------------------------------------------------------
> >>>> *Router config*:
> >>>> *
> >>>> !
> >>>> !
> >>>> !
> >>>> multilink bundle-name authenticated
> >>>> !
> >>>> chat-script gsm "" "ATDT*99*1#" TIMEOUT 60 "CONNECT"
> >>>> !
> >>>> !
> >>>> !
> >>>> !
> >>>> interface Loopback0
> >>>> ip address 10.0.0.1 255.255.255.0
> >>>> !
> >>>> interface Wlan-GigabitEthernet0/0
> >>>> description Internal switch interface connecting to the embedded AP
> >>>> !
> >>>> interface GigabitEthernet0/0
> >>>> no ip address
> >>>> shutdown
> >>>> duplex auto
> >>>> speed auto
> >>>> !
> >>>> interface wlan-ap0
> >>>> description Service module interface to manage the embedded AP
> >>>> no ip address
> >>>> arp timeout 0
> >>>> no mop enabled
> >>>> no mop sysid
> >>>> !
> >>>> interface GigabitEthernet0/1
> >>>> no ip address
> >>>> shutdown
> >>>> duplex auto
> >>>> speed auto
> >>>> !
> >>>> interface ATM0/0/0
> >>>> no ip address
> >>>> shutdown
> >>>> no atm ilmi-keepalive
> >>>> !
> >>>> interface Cellular0/1/0
> >>>> ip address negotiated
> >>>> encapsulation ppp
> >>>> dialer in-band
> >>>> dialer idle-timeout 30
> >>>> dialer string gsm
> >>>> dialer-group 1
> >>>> async mode interactive
> >>>> ppp ipcp dns request
> >>>> !
> >>>> interface Vlan1
> >>>> no ip address
> >>>> !
> >>>> ip forward-protocol nd
> >>>> !
> >>>> no ip http server
> >>>> no ip http secure-server
> >>>> !
> >>>> ip route 0.0.0.0 0.0.0.0 Cellular0/1/0
> >>>> !
> >>>> access-list 1 permit any
> >>>> dialer-list 1 protocol ip list 1
> >>>> !
> >>>> !
> >>>> !
> >>>> control-plane
> >>>> !
> >>>> !
> >>>> line con 0
> >>>> line aux 0
> >>>> line 0/1/0
> >>>> exec-timeout 0 0
> >>>> script dialer gsm
> >>>> login
> >>>> modem InOut
> >>>> no exec
> >>>> speed 80000
> >>>> line 67
> >>>> no activation-character
> >>>> no exec
> >>>> transport preferred none
> >>>> transport input all
> >>>> transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
> >>>> line vty 0 4
> >>>> login
> >>>> !
> >>>> scheduler allocate 20000 1000
> >>>> end*
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>>
> >>>> kindly Guid me
> >>>>
> >>>>
> >>>> Blogs and organic groups at http://www.ccie.net
> >>>>
> >>>>
> _______________________________________________________________________
> >>>> Subscription information may be found at:
> >>>> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Sun Oct 31 2010 - 00:36:29 ART