Dear Bilal
Router#show cellular 0/1/0 all
Hardware Information
====================
Modem Firmware Version = H1_1_9_3MCAP C:/WS/
Modem Firmware built = 12/12/07
Hardware Version = 1.0
International Mobile Subscriber Identity (IMSI) = 606010105114370
International Mobile Equipment Identity (IMEI) = 011359000487907
Factory Serial Number (FSN) = D28026013381043
Modem Status = Online
Current Modem Temperature = 26 deg C, State = Normal
Profile Information
====================
Profile 1 = INACTIVE*
--------
PDP Type = IPv4
Access Point Name (APN) = almadar.net
Authentication = None
Username: , Password:
* - Default profile
Data Connection Information
===========================
Data Transmitted = 0 bytes, Received = 0 bytes
Profile 1, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 2, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 3, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 4, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 5, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 6, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 7, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 8, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 9, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 10, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 11, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 12, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 13, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 14, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 15, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Profile 16, Packet Session Status = INACTIVE
Inactivity Reason = Normal inactivate state
Network Information
===================
Current Service Status = Normal, Service Error = None
Current Service = Combined
Packet Service = GPRS (Attached)
Packet Session Status = Inactive
Current Roaming Status = Home
Network Selection Mode = Automatic
Country = 606, Network = 606 01
Mobile Country Code (MCC) = 606
Mobile Network Code (MNC) = 1
Location Area Code (LAC) = 1
Routing Area Code (RAC) = 1
Cell ID = 11071
Primary Scrambling Code = 0
PLMN Selection = Automatic
Registered PLMN = Libya Al Madar , Abbreviated = 606 01
Service Provider = 606 01
Radio Information
=================
Current Band = GSM 900, Channel Number = 5
Current RSSI = -62 dBm
Band Selected = Auto
Modem Security Information
==========================
Card Holder Verification (CHV1) = Disabled
SIM Status = OK
SIM User Operation Required = None
Number of Retries remaining = 3
Thanks
On Sat, Oct 30, 2010 at 2:42 PM, Bilal Hansrod <bilal.hansrod_at_gmail.com>wrote:
> Can you please send the output of *sh cell 0/1/0 all*
>
>
> Bilal
>
>
> On Sat, Oct 30, 2010 at 11:36 PM, muhammad adnan <taurusadnan19_at_gmail.com>wrote:
>
>> Dear Bilal i configure according to the Cisco Documentation
>> and in my mail i pasted show run config...
>>
>>
>>
>> http://www.cisco.com/en/US/docs/routers/access/1800/1861/software/feature/guide/mrwlsgsm.html#wp1040391
>>
>> in my mail i ask that username and password is blank to access the
>> internet
>> Service provider ask me no authentication username and password blank ("i
>> just put Apn in my phone and username and password blank and it works fine
>> accessing the internet")
>>
>> if u need any more information kindly let me know again..
>>
>> Thanks
>> Muhammad Adnan
>>
>>
>>
>> On Sat, Oct 30, 2010 at 2:28 PM, Bilal Hansrod <bilal.hansrod_at_gmail.com>wrote:
>>
>>> Hi Muhammad,
>>>
>>> I can't see a logical interface created for cell interface where you
>>> define your PPP username/password and also the authentication method.
>>>
>>> An example from my config as below:
>>>
>>>
>>> interface Dialer1
>>> ip address negotiated
>>> ip virtual-reassembly
>>> encapsulation ppp
>>> dialer pool 1
>>> dialer idle-timeout 0
>>> dialer string gsm
>>> dialer persistent
>>> dialer-group 1
>>> no cdp enable
>>> ppp authentication chap callin
>>> ppp chap hostname XXX
>>> ppp chap password YYY
>>>
>>>
>>> Regards,
>>>
>>> Bilal
>>>
>>>
>>> On Sat, Oct 30, 2010 at 11:05 PM, muhammad adnan <
>>> taurusadnan19_at_gmail.com> wrote:
>>>
>>>> Dear Group members:-
>>>> i am trying to configure the 3G-module.i
>>>> have inserted my sim card into the HWIC module sim card properly
>>>> working in
>>>> the phone and i am accessing the internet.
>>>> but when i configure HWIC module accordingly i am unable to access the
>>>> internet my configration pasted below if any experience person guid me
>>>> little.
>>>>
>>>>
>>>> in my phone i just put APN and it work fine without Authentication
>>>> *Service
>>>> provider ask me* that the *username and password is blank..*
>>>>
>>>> country Libya
>>>> GSM service provider =Almadar
>>>> APN or access point name =almadar.net
>>>>
>>>>
>>>>
>>>>
>>>> *Router#show cellular 0/1/0 profile
>>>> Profile 1 = INACTIVE*
>>>> --------
>>>> PDP Type = IPv4
>>>> Access Point Name (APN) = almadar.net
>>>> Authentication = None
>>>> Username: , Password:
>>>>
>>>> * - Default profile
>>>> *
>>>>
>>>> --------------------------------------------------------------------------------------
>>>> *Router config*:
>>>> *
>>>> !
>>>> !
>>>> !
>>>> multilink bundle-name authenticated
>>>> !
>>>> chat-script gsm "" "ATDT*99*1#" TIMEOUT 60 "CONNECT"
>>>> !
>>>> !
>>>> !
>>>> !
>>>> interface Loopback0
>>>> ip address 10.0.0.1 255.255.255.0
>>>> !
>>>> interface Wlan-GigabitEthernet0/0
>>>> description Internal switch interface connecting to the embedded AP
>>>> !
>>>> interface GigabitEthernet0/0
>>>> no ip address
>>>> shutdown
>>>> duplex auto
>>>> speed auto
>>>> !
>>>> interface wlan-ap0
>>>> description Service module interface to manage the embedded AP
>>>> no ip address
>>>> arp timeout 0
>>>> no mop enabled
>>>> no mop sysid
>>>> !
>>>> interface GigabitEthernet0/1
>>>> no ip address
>>>> shutdown
>>>> duplex auto
>>>> speed auto
>>>> !
>>>> interface ATM0/0/0
>>>> no ip address
>>>> shutdown
>>>> no atm ilmi-keepalive
>>>> !
>>>> interface Cellular0/1/0
>>>> ip address negotiated
>>>> encapsulation ppp
>>>> dialer in-band
>>>> dialer idle-timeout 30
>>>> dialer string gsm
>>>> dialer-group 1
>>>> async mode interactive
>>>> ppp ipcp dns request
>>>> !
>>>> interface Vlan1
>>>> no ip address
>>>> !
>>>> ip forward-protocol nd
>>>> !
>>>> no ip http server
>>>> no ip http secure-server
>>>> !
>>>> ip route 0.0.0.0 0.0.0.0 Cellular0/1/0
>>>> !
>>>> access-list 1 permit any
>>>> dialer-list 1 protocol ip list 1
>>>> !
>>>> !
>>>> !
>>>> control-plane
>>>> !
>>>> !
>>>> line con 0
>>>> line aux 0
>>>> line 0/1/0
>>>> exec-timeout 0 0
>>>> script dialer gsm
>>>> login
>>>> modem InOut
>>>> no exec
>>>> speed 80000
>>>> line 67
>>>> no activation-character
>>>> no exec
>>>> transport preferred none
>>>> transport input all
>>>> transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
>>>> line vty 0 4
>>>> login
>>>> !
>>>> scheduler allocate 20000 1000
>>>> end*
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>
>>>> kindly Guid me
>>>>
>>>>
>>>> Blogs and organic groups at http://www.ccie.net
>>>>
>>>> _______________________________________________________________________
>>>> Subscription information may be found at:
>>>> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
Received on Sat Oct 30 2010 - 14:56:58 ART
This archive was generated by hypermail 2.2.0 : Mon Nov 01 2010 - 06:42:06 ART