Re: E1 interface

 
Thanks for your reply
 
 
find below the output
 
 
 
#sh controllers e1 0/4
E1 0/4 is down.
  Applique type is Channelized E1 - balanced
  Receiver is getting AIS.
  alarm-trigger is not set
  Version info Firmware: 20040108, FPGA: 11
  Framing is NO-CRC4, Line Code is HDB3, Clock Source is Line.
  CRC Threshold is 320. Reported from firmware is 320.
  Data in current interval (105 seconds elapsed):
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 105 Unavail Secs
  Data in Interval 1:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
  Data in Interval 2:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
  Data in Interval 3:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
  Data in Interval 4:
     2111 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
  Data in Interval 5:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
  Data in Interval 6:
     2595 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
  Data in Interval 7:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
  Data in Interval 8:
     3934044 Line Code Violations, 15100 Path Code Violations
     13 Slip Secs, 4 Fr Loss Secs, 20 Line Err Secs, 0 Degraded Mins
     2 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 887 Unavail Secs
  Data in Interval 9:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
  Data in Interval 10:
     1073 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
  Data in Interval 11:
     3 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
  Data in Interval 12:
     0 Line Code Violations, 0 Path Code Violations
     0 Slip Secs, 0 Fr Loss Secs, 0 Line Err Secs, 0 Degraded Mins
     0 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 900 Unavail Secs
  Total Data (last 12 15 minute intervals):
     3939826 Line Code Violations, 15100 Path Code Violations,
     13 Slip Secs, 4 Fr Loss Secs, 20 Line Err Secs, 0 Degraded Mins,
     2 Errored Secs, 0 Bursty Err Secs, 0 Severely Err Secs, 10787 Unavail
Secs

--- On Tue, 9/14/10, Andy Reid <ccie_at_reid.it> wrote:

From: Andy Reid <ccie_at_reid.it>
Subject: Re: E1 interface
To: "Abiola Jewoola" <biola_y2k_at_yahoo.com>
Cc: ccielab_at_groupstudy.com
Date: Tuesday, September 14, 2010, 4:21 AM

Hi,

Please provide the show controller output when a physical loop is applied to
the port and the controller clock is set to internal.

Also remember that the E1 pins outs are different to Ethernet eventhough they
both physically present on an RJ45.

regards Andy

Abiola Jewoola wrote:
> hello GS
> i have a VWIC-1MFT-E1 card installed on a 3700 series router which is to
be
> connected to an E1 radio for data traffic . i have done the initial config
in
> bringing the E1 card up
> But the E1 interface is still down
> controller E1 1/0
> framing crc4
> linecode hdb3
> channel-group 0 timeslots 1-31
> no shut
> i can see the serial interface when i do sh ip int bri and sh ver
> Any ideas as to why d e1 int is down?
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>
>

Blogs and organic groups at http://www.ccie.net
Received on Tue Sep 14 2010 - 04:53:20 ART