Re: Internetwork Expert's R&S Topology

Thank you everyone for your support & kind words. I finally got it to work yesterday. It's eating up my CPU but @ this point am just happy it works. I am sure there are tweaks for that.

Once again. Thank you all.

Best regards.

Babatunde Sanda
:: Sent from my Iphone. Apologies for errors and brevity. ::

On Sep 12, 2010, at 5:16 PM, "Babatunde Sanda" <sbabatunde1_at_ca.rr.com> wrote:

> Thanks Bobola. I actually have reviewed and still going over the video
> again. It was in there they mentioned to replace with the file that is not
> working for me.
>
> Oh well, I'II keep at it since I don't have a choice now.
>
> Thanks.
>
>
> -----Original Message-----
> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
> Bobola Oke
> Sent: Sunday, September 12, 2010 3:42 PM
> To: Babatunde Sanda
> Cc: Segun Daini; Cisco certification
> Subject: Re: Internetwork Expert's R&S Topology
>
> Meen Tunde, sorry o....
> the 7200 and 7201 are used as well as udp ports for communication among the
> virtual devices check this out:
>
> http://classroom.internetworkexpert.com/p27794135/
>
> best of luck
>
> On 9/12/10, Babatunde Sanda <sbabatunde1_at_ca.rr.com> wrote:
>> Thanks for the hint Segun but aren't the 7200 & 7201 the ports being used?
>> Or are you referring to something else in the install?
>>
>> Thanks.
>>
>> Babatunde Sanda
>> :: Sent from my Iphone. Apologies for errors and brevity. ::
>>
>> On Sep 11, 2010, at 10:25 PM, Segun Daini <segundaini_at_gmail.com> wrote:
>>
>>> Hi Tunde,
>>>
>>> What is ur base udp port? The default is 10000. Change that value. My
>>> guess is you've got another process using that port.
>>>
>>> Regards.
>>>
>>> On 11 Sep 2010 23:45, "Babatunde Sanda" <sbabatunde1_at_ca.rr.com> wrote:
>>>
>>> A little help with dynamips guys. So I have followed the videos and
>>> have successfully installed needed programs. But when I click
>>> Dynamips server the session comes up and then disappears. If I edit
>>> it with notepad I see this
>>>
>>> @echo off
>>> rem Launch a local copy of dynamips
>>> start /belownormal /min "Dynamips" "dynamips.exe" -H 7200 start
>>> /belownormal /min "Dynamips" "dynamips.exe" -H 7201
>>>
>>> I am trying to make it work in Windows 7. Is there something am missing.
>>>
>>>
>>> If I don't change the "dynamips-start.cmd" as stated in the tutorial
>>> video the dynamips server loads. But below is what is in the file
>>>
>>> @echo off
>>> rem Launch a local copy of dynamips
>>> set dynamips=%CD%\dynamips.exe
>>> cd %TEMP%
>>> start /belownormal "Dynamips" cmd /c ""%dynamips%" -H 7200 & pause"
>>>
>>>
>>> Any hint appreciated. Still trying but getting nowhere so far.
>>>
>>>
>>>
>>>
>>>
>>> -----Original Message-----
>>> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf ...
>>>
>>>
>>> Blogs and organic groups at http://www.ccie.net
>>>
>>> _____________________________________________________________________
>>> __ Subscription information may be found at:
>>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> ______________________________________________________________________
>> _ Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>>
>>
>>
>>
>>
>
>
> --
> Bobola Oke
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Mon Sep 13 2010 - 10:26:47 ART