Re: GNS3 Issues during PfR Lab

Hey Adrian,

Two questions:)

1. Are you running GNS3 FR switch?
2. Which routing protocol you configured for PfR lab?

Regards,

Bilal

On Wed, Aug 25, 2010 at 9:21 PM, Adrian Brayton <abrayton_at_gmail.com> wrote:

> AMEN "you can do alot of great things with GNS3, but it is what it is..."
>
> I have no issue's running OER / PfR on GNS3 but just yesterday I couldn't
> ping another interface on the same switch, same subnet until I shut
> everything down "Closed GNS3 and reopened the topology" and then pasted the
> configs back in and it worked fine from then on! It was the exact same
> config I pasted in before but 2 hours later! :)
>
> There is no replacement for real hardware!
>
>
> On Aug 25, 2010, at 6:09 AM, garry baker wrote:
>
> > you can do alot of great things with GNS3, but it is what it is...
> >
> > and the limits are different and always dependent on your mix of
> > protocols...
> >
> > i know that doesn't help your exact issue but it is the case that i have
> run
> > into many many times...
> >
> > one size does not fit all...
> >
> > but then again maybe somebody on the list has done the pfr lab and can
> give
> > you the magic bullet, ie IOS and platform and idle code to even it all
> > out...
> >
> > good luck and hoping to hear success...
> >
> >
> > --
> > Garry L. Baker
> >
> > "There is no 'patch' for stupidity." - www.sqlsecurity.com
> >
> >
> > On Wed, Aug 25, 2010 at 12:59 PM, Bilal Hansrod <bilal.hansrod_at_gmail.com
> >wrote:
> >
> >> Hello Guys,
> >>
> >> I have encounter really weird and funny issues on GNS3 lab. I got 6G of
> >> memory, i7 Processor and running on Ubuntu x64. It is brand new PC
> >> optimised
> >> for CCIE lab. I have setup idle timers and CPU load for one core is
> below
> >> 20%. I have started with INE W1 till I reached the PfR lab [3.15].
> >> Once I enable IP SLA on R1 and R6 and policies on R5 (MC) , it seems
> that I
> >> have serial interface flapping. Also, copy via Http fails and I can see
> my
> >> IP sla on R1 is timing out while copying IOS from SW2. As per Stephen
> and
> >> David's suggestion, I disbaled keepalive on serial interface, but still
> no
> >> luck.
> >>
> >> I am stuck in this limbo and I can proceed and just wondering what will
> >> happen when I turn on EIGRP, BGP, and redistribution.
> >>
> >> Please anyone out there, who can advise any workable solution.
> >>
> >> Any suggestions and comments would be highly appreciated.
> >>
> >> Regards,
> >>
> >> Bilal
> >>
> >>
> >> Blogs and organic groups at http://www.ccie.net
> >>
> >> _______________________________________________________________________
> >> Subscription information may be found at:
> >> http://www.groupstudy.com/list/CCIELab.html
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Wed Aug 25 2010 - 21:24:45 ART