Re: IPV6 ROUTER EIGRP AS#

I can see the same CLI present in ISRs as well .
I am using c2811 presently and it can be seen there :

R1(config)#ipv6 unicast-routing
R1(config)#ipv6 router eigrp 10
R1(config-rtr)#def
R1(config-rtr)#default?
default default-information default-metric

R1(config-rtr)#do sh ver | inc IOS
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9_SNA-M),
Version 12.4(20)T, RELEASE SOFTWARE (fc3)
R1(config-rtr)#

Thnx
Gaurav Madan
CCIE # 23863

On Tue, Aug 17, 2010 at 11:01 AM, Sonu Khandelwal (sokhande)
<sokhande_at_cisco.com> wrote:
> What is your image version? I see it on my router.
>
> R1(config-if)#ipv6 router eig 1
> R1(config-rtr)#de
> R1(config-rtr)#default?
> default default-information default-metric
>
> R1(config-rtr)#default-
> R1(config-rtr)#default-?
> default-information default-metric
>
> R1(config-rtr)#default-me
> R1(config-rtr)#default-metric ?
> <1-4294967295> Bandwidth in Kbits per second
>
> R1(config-rtr)#default-metric
>
> Thanks,
> Sonu
>
> -----Original Message-----
> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
> Elliott Reyes
> Sent: Tuesday, August 17, 2010 9:14 AM
> To: garry baker
> Cc: Cisco certification
> Subject: Re: IPV6 ROUTER EIGRP AS#
>
> Funny I didn't see it either on my same software and hardware..
>
> INE ?
>
>
>
> On Mon, Aug 16, 2010 at 12:35 PM, garry baker <baker.garry_at_gmail.com>
> wrote:
>
>> command reference says it exists:
>>
>>
>>
> http://www.cisco.com/en/US/docs/ios/ipv6/command/reference/ipv6_04.html#
> wp2372182
>>
>> but not in my router with Cisco IOS Software, 3700 Software
>> (C3725-ADVENTERPRISEK9-M), Version 12.4(15)T12, RELEASE SOFTWARE (fc3)
>>
>> Router(config)#ipv6 router eigrp 1
>> Router(config-rtr)#?
>> default Set a command to its defaults
>> distance Administrative distance
>> distribute-list Filter networks in routing updates
>> exit Exit from IPv6 routing protocol configuration
> mode
>> log-neighbor-changes Enable/Disable EIGRP neighbor logging
>> log-neighbor-warnings Enable/Disable EIGRP neighbor warnings
>> maximum-paths Forward packets over multiple paths
>> metric Modify EIGRP routing metrics and parameters
>> neighbor Specify a neighbor router
>> no Negate a command or set its defaults
>> passive-interface Suppress routing updates on an interface
>> redistribute Redistribute IPv6 prefixes from another
> routing
>> protocol
>> router-id router-id for this EIGRP process
>> shutdown Shutdown protocol
>> stub Set EIGRP as stubbed router
>> timers Adjust routing timers
>> variance Control load balancing variance
>>
>> --
>> Garry L. Baker
>>
>> "There is no 'patch' for stupidity." - www.sqlsecurity.com
>>
>>
>> On Mon, Aug 16, 2010 at 10:07 PM, Elliott Reyes <
>> fontananetworkengineer_at_gmail.com> wrote:
>>
>>> Under ipv6 router eigrp (AS)
>>>
>>> I was doing the INE Lab 12 section 3.5 task and peaked at the
> solution
>>> guide
>>>
>>> It say's to add the
>>>
>>> default-metric command in there. I don't see it on my code level and
> under
>>> the command guide it say's that's only for IPV6 OSPF
>>>
>>> Is that right ?
>>>
>>> Thanks,
>>>
>>> Elliott
>>>
>>>
>>> Blogs and organic groups at http://www.ccie.net
>>>
>>>
> _______________________________________________________________________
>>> Subscription information may be found at:
>>> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Tue Aug 17 2010 - 11:37:18 ART