Re: sparse OIL problem

solved, pim was not enabled on SW-04 vlan 10

On Fri, Aug 13, 2010 at 2:10 AM, Kambiz Agahian <aussiecert_at_gmail.com>wrote:

> Double check the R5's interface configuration.
>
> HTH
>
> Kambiz Agahian
>
> CCIE Instructor/Consultant
> M.Eng Telecom, CCIE# 25341, CCSI# 33326, MCSE, MCSA
>
>
>
>
> On Thu, Aug 12, 2010 at 5:32 AM, garry baker <baker.garry_at_gmail.com>wrote:
>
>> check the RPF to your mulicast source and groups, do you have PIM on all
>> your interfaces or trying to get it to go a certain direction, check the
>> unicast path to see if it is going the same way you want you mulitcast to
>> go...
>>
>>
>>
>>
>> On Thu, Aug 12, 2010 at 2:48 PM, masroor ali <masror.ali_at_gmail.com>
>> wrote:
>>
>> > hi,
>> >
>> > R6-----------------R4
>> > | |
>> > | |
>> > R1 |
>> > \ |
>> > \ /
>> > R5
>> > |
>> > |
>> > SW2
>> > |
>> > SW4
>> >
>> > I am running sprase-mode with static RP address, which is R5 lo0, when I
>> > ping from R6 to group 224.20.20.20 which is configured at vlan 10 int of
>> > SW4, I get the below debug message at R4,
>> >
>> > *Mar 1 02:10:48.127: IP(0): s=155.1.146.6 (Ethernet0/1) d=224.20.20.20
>> > id=18, ttl=254, prot=1, len=114(100), mroute olist null
>> >
>> > please find the attached configuration for reference.
>> > --
>> > Regards,
>> > Masroor Ali
>> > Rack1SW4#show runn
>> > Rack1SW4#show running-config
>> > Building configuration...
>> >
>> > Current configuration : 2088 bytes
>> > !
>> > version 12.4
>> > service timestamps debug datetime msec
>> > service timestamps log datetime msec
>> > no service password-encryption
>> > !
>> > hostname Rack1SW4
>> > !
>> > boot-start-marker
>> > boot-end-marker
>> > !
>> > enable password cisco
>> > !
>> > no aaa new-model
>> > memory-size iomem 5
>> > !
>> > !
>> > ip cef
>> > no ip domain lookup
>> > !
>> > !
>> > ip multicast-routing
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > interface Loopback0
>> > ip address 150.1.10.10 255.255.255.255
>> > !
>> > interface FastEthernet1/0
>> > !
>> > interface FastEthernet1/1
>> > !
>> > interface FastEthernet1/2
>> > !
>> > interface FastEthernet1/3
>> > !
>> > interface FastEthernet1/4
>> > description To R4 E0/1
>> > switchport access vlan 146
>> > !
>> > interface FastEthernet1/5
>> > !
>> > interface FastEthernet1/6
>> > description To R6 E0/1
>> > switchport mode trunk
>> > !
>> > interface FastEthernet1/7
>> > description To SW1 F1/13
>> > switchport mode trunk
>> > !
>> > interface FastEthernet1/8
>> > description To SW1 F1/14
>> > switchport mode trunk
>> > !
>> > interface FastEthernet1/9
>> > description To SW1 F1/15
>> > switchport mode trunk
>> > !
>> > interface FastEthernet1/10
>> > description To SW2 F1/13
>> > no switchport
>> > ip address 155.1.108.10 255.255.255.0
>> > ip pim sparse-mode
>> > !
>> > interface FastEthernet1/11
>> > description To SW2 F1/14
>> > switchport mode trunk
>> > !
>> > interface FastEthernet1/12
>> > description To SW2 F1/15
>> > switchport mode trunk
>> > !
>> > interface FastEthernet1/13
>> > description To SW3 F1/13
>> > switchport mode trunk
>> > !
>> > interface FastEthernet1/14
>> > description To SW3 F1/14
>> > switchport mode trunk
>> > !
>> > interface FastEthernet1/15
>> > description To SW3 F1/15
>> > switchport mode trunk
>> > !
>> > interface Vlan1
>> > no ip address
>> > !
>> > interface Vlan10
>> > ip address 155.1.10.10 255.255.255.0
>> > ip igmp join-group 224.10.10.10
>> > ip igmp join-group 224.20.20.20
>> > !
>> > router eigrp 100
>> > network 150.1.0.0
>> > network 155.1.0.0
>> > no auto-summary
>> > !
>> > ip http server
>> > ip forward-protocol nd
>> > !
>> > !
>> > ip pim rp-address 150.1.5.5
>> > !
>> > !
>> > !
>> > !
>> > control-plane
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > alias exec s show ip int bri
>> > alias exec sr show runn
>> > alias exec c configure terminal
>> > alias exec r show ip route
>> > alias exec v show vlan-switch
>> > !
>> > line con 0
>> > Rack1R6#show run
>> > Rack1R6#show running-config
>> > Building configuration...
>> >
>> > Current configuration : 1594 bytes
>> > !
>> > version 12.4
>> > service timestamps debug datetime msec
>> > service timestamps log datetime msec
>> > no service password-encryption
>> > !
>> > hostname Rack1R6
>> > !
>> > boot-start-marker
>> > boot-end-marker
>> > !
>> > enable password cisco
>> > !
>> > no aaa new-model
>> > memory-size iomem 5
>> > !
>> > !
>> > ip cef
>> > no ip domain lookup
>> > !
>> > !
>> > ip multicast-routing
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > interface Loopback6
>> > ip address 150.1.6.6 255.255.255.255
>> > !
>> > interface Ethernet0/0
>> > no ip address
>> > full-duplex
>> > !
>> > interface Ethernet0/1
>> > no ip address
>> > full-duplex
>> > !
>> > interface Ethernet0/1.67
>> > encapsulation dot1Q 67
>> > ip address 155.1.67.6 255.255.255.0
>> > !
>> > interface Ethernet0/1.146
>> > encapsulation dot1Q 146
>> > ip address 155.1.146.6 255.255.255.0
>> > ip pim sparse-mode
>> > !
>> > interface Ethernet0/2
>> > no ip address
>> > shutdown
>> > half-duplex
>> > !
>> > interface Ethernet0/3
>> > no ip address
>> > shutdown
>> > half-duplex
>> > !
>> > interface Serial1/0
>> > no ip address
>> > shutdown
>> > serial restart-delay 0
>> > !
>> > interface Serial1/1
>> > no ip address
>> > shutdown
>> > serial restart-delay 0
>> > !
>> > interface Serial1/2
>> > no ip address
>> > shutdown
>> > serial restart-delay 0
>> > !
>> > interface Serial1/3
>> > no ip address
>> > shutdown
>> > serial restart-delay 0
>> > !
>> > router eigrp 100
>> > network 150.1.0.0
>> > network 155.1.0.0
>> > no auto-summary
>> > !
>> > ip http server
>> > ip forward-protocol nd
>> > !
>> > !
>> > ip pim rp-address 150.1.5.5
>> > !
>> > !
>> > !
>> > !
>> > control-plane
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > alias exec s show ip int bri
>> > alias exec sr show runn
>> > alias exec c configure terminal
>> > alias exec r show ip route
>> > alias exec v show vlan-switch
>> > !
>> > line con 0
>> > exec-timeout 0 0
>> > privilege level 15
>> > logging synchronous
>> > line aux 0
>> > exec-timeout 0 0
>> > privilege level 15
>> > line vty 0 4
>> > password cisco
>> > login
>> > !
>> > !
>> > end
>> > Rack1R4#show runn
>> > Rack1R4#show running-config
>> > Building configuration...
>> >
>> > Current configuration : 1820 bytes
>> > !
>> > version 12.4
>> > service timestamps debug datetime msec
>> > service timestamps log datetime msec
>> > no service password-encryption
>> > !
>> > hostname Rack1R4
>> > !
>> > boot-start-marker
>> > boot-end-marker
>> > !
>> > enable password cisco
>> > !
>> > no aaa new-model
>> > memory-size iomem 5
>> > !
>> > !
>> > ip cef
>> > no ip domain lookup
>> > !
>> > !
>> > ip multicast-routing
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > interface Loopback0
>> > ip address 150.1.4.4 255.255.255.255
>> > !
>> > interface Ethernet0/0
>> > ip address 204.12.1.4 255.255.255.0
>> > full-duplex
>> > !
>> > interface Ethernet0/1
>> > ip address 155.1.146.4 255.255.255.0
>> > ip pim sparse-mode
>> > full-duplex
>> > !
>> > interface Ethernet0/2
>> > no ip address
>> > shutdown
>> > half-duplex
>> > !
>> > interface Ethernet0/3
>> > no ip address
>> > shutdown
>> > half-duplex
>> > !
>> > interface Serial1/0
>> > ip address 155.1.0.4 255.255.255.0
>> > ip hello-interval eigrp 100 30
>> > ip hold-time eigrp 100 60
>> > encapsulation frame-relay
>> > serial restart-delay 0
>> > frame-relay map ip 155.1.0.1 405 broadcast
>> > frame-relay map ip 155.1.0.2 405 broadcast
>> > frame-relay map ip 155.1.0.3 405 broadcast
>> > frame-relay map ip 155.1.0.5 405 broadcast
>> > no frame-relay inverse-arp
>> > frame-relay lmi-type ansi
>> > !
>> > interface Serial1/1
>> > ip address 155.1.45.4 255.255.255.0
>> > ip pim sparse-mode
>> > serial restart-delay 0
>> > !
>> > interface Serial1/2
>> > no ip address
>> > shutdown
>> > serial restart-delay 0
>> > !
>> > interface Serial1/3
>> > no ip address
>> > shutdown
>> > serial restart-delay 0
>> > !
>> > router eigrp 100
>> > network 150.1.0.0
>> > network 155.1.0.0
>> > no auto-summary
>> > !
>> > ip http server
>> > ip forward-protocol nd
>> > !
>> > !
>> > ip pim rp-address 150.1.5.5
>> > !
>> > !
>> > !
>> > !
>> > control-plane
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > alias exec s show ip int bri
>> > alias exec sr show runn
>> > alias exec c configure terminal
>> > alias exec r show ip route
>> > alias exec v show vlan-switch
>> > !
>> > line con 0
>> > exec-timeout 0 0
>> > privilege level 15
>> > logging synchronous
>> > line aux 0
>> > exec-timeout 0 0
>> > privilege level 15
>> > line vty 0 4
>> > password cisco
>> > login
>> > !
>> > !
>> > end
>> >
>> >
>> > *Mar 1 02:21:14.599: IP(0): s=155.1.146.6 (Ethernet0/1) d=224.20.20.20
>> > id=19, ttl=254, prot=1, len=114(100), mroute olist null
>> > Rack1R4#
>> > Rack1R4#
>> > Rack1R4#
>> > Rack1R4#show ip mroute
>> > IP Multicast Routing Table
>> > Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C -
>> > Connected,
>> > L - Local, P - Pruned, R - RP-bit set, F - Register flag,
>> > T - SPT-bit set, J - Join SPT, M - MSDP created entry,
>> > X - Proxy Join Timer Running, A - Candidate for MSDP
>> Advertisement,
>> > U - URD, I - Received Source Specific Host Report,
>> > Z - Multicast Tunnel, z - MDT-data group sender,
>> > Y - Joined MDT-data group, y - Sending to MDT-data group
>> > Outgoing interface flags: H - Hardware switched, A - Assert winner
>> > Timers: Uptime/Expires
>> > Interface state: Interface, Next-Hop or VCD, State/Mode
>> >
>> > (*, 224.20.20.20), 00:00:07/stopped, RP 150.1.5.5, flags: SP
>> > Incoming interface: Serial1/1, RPF nbr 155.1.45.5
>> > Outgoing interface list: Null
>> >
>> > (155.1.146.6, 224.20.20.20), 00:00:07/00:02:52, flags: PT
>> > Incoming interface: Ethernet0/1, RPF nbr 155.1.146.6
>> > Outgoing interface list: Null
>> >
>> > (*, 224.0.1.40), 01:27:17/00:02:40, RP 150.1.5.5, flags: SJCL
>> > Incoming interface: Serial1/1, RPF nbr 155.1.45.5
>> > Outgoing interface list:
>> > Ethernet0/1, Forward/Sparse, 01:03:58/00:02:51
>> >
>> > Rack1R4#show ip rou
>> > Rack1R4#show ip route 155.1.146.6
>> > Routing entry for 155.1.146.0/24
>> > Known via "connected", distance 0, metric 0 (connected, via interface)
>> > Redistributing via eigrp 100
>> > Routing Descriptor Blocks:
>> > * directly connected, via Ethernet0/1
>> > Route metric is 0, traffic share count is 1
>> > Rack1R5#show runn
>> > Rack1R5#show running-config
>> > Building configuration...
>> >
>> > Current configuration : 1871 bytes
>> > !
>> > version 12.4
>> > service timestamps debug datetime msec
>> > service timestamps log datetime msec
>> > no service password-encryption
>> > !
>> > hostname Rack1R5
>> > !
>> > boot-start-marker
>> > boot-end-marker
>> > !
>> > enable password cisco
>> > !
>> > no aaa new-model
>> > memory-size iomem 5
>> > !
>> > !
>> > ip cef
>> > no ip domain lookup
>> > !
>> > !
>> > ip multicast-routing
>> > ip multicast rpf interval 6
>> > ip multicast rpf backoff 10 200
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > interface Loopback0
>> > ip address 150.1.5.5 255.255.255.255
>> > !
>> > interface Ethernet0/0
>> > ip address 155.1.58.5 255.255.255.0
>> > ip pim sparse-mode
>> > full-duplex
>> > !
>> > interface Ethernet0/1
>> > ip address 155.1.5.5 255.255.255.0
>> > full-duplex
>> > !
>> > interface Ethernet0/2
>> > no ip address
>> > shutdown
>> > half-duplex
>> > !
>> > interface Ethernet0/3
>> > no ip address
>> > shutdown
>> > half-duplex
>> > !
>> > interface Serial1/0
>> > ip address 155.1.0.5 255.255.255.0
>> > ip hello-interval eigrp 100 30
>> > ip hold-time eigrp 100 60
>> > ip pim sparse-mode
>> > encapsulation frame-relay
>> > serial restart-delay 0
>> > frame-relay map ip 155.1.0.1 501 broadcast
>> > frame-relay map ip 155.1.0.2 501 broadcast
>> > frame-relay map ip 155.1.0.3 501 broadcast
>> > frame-relay map ip 155.1.0.4 501 broadcast
>> > no frame-relay inverse-arp
>> > !
>> > interface Serial1/1
>> > ip address 155.1.45.5 255.255.255.0
>> > ip pim sparse-mode
>> > serial restart-delay 0
>> > !
>> > interface Serial1/2
>> > no ip address
>> > shutdown
>> > serial restart-delay 0
>> > !
>> > interface Serial1/3
>> > no ip address
>> > shutdown
>> > serial restart-delay 0
>> > !
>> > router eigrp 100
>> > network 150.1.0.0
>> > network 155.1.0.0
>> > no auto-summary
>> > !
>> > ip http server
>> > ip forward-protocol nd
>> > !
>> > !
>> > ip pim rp-address 150.1.5.5
>> > !
>> > !
>> > !
>> > !
>> > control-plane
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > !
>> > alias exec s show ip int bri
>> > alias exec sr show runn
>> > alias exec c configure terminal
>> > alias exec r show ip route
>> > alias exec v show vlan-switch
>> > !
>> > line con 0
>> > exec-timeout 0 0
>> > privilege level 15
>> > logging synchronous
>> > line aux 0
>> > exec-timeout 0 0
>> > privilege level 15
>> > line vty 0 4
>> > password cisco
>> > login
>> > !
>> > !
>> > end
>> >
>> >
>> > Blogs and organic groups at http://www.ccie.net
>> >
>> > _______________________________________________________________________
>> > Subscription information may be found at:
>> > http://www.groupstudy.com/list/CCIELab.html
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>>
>>
>>
>>
>>
>

-- 
Regards,
Masroor Ali
Blogs and organic groups at http://www.ccie.net