Re: Frame Relay Interface Configuration problem

Sonu couldnt have helped more than that .!

On Tue, Aug 10, 2010 at 8:48 PM, Sonu Khandelwal (sokhande)
<sokhande_at_cisco.com> wrote:
> Spot on!!!
>
> Yes, ppp over frame-relay is the solution!!!
>
> I just tried to simulate using following topology and it worked for me.
>
> R2---R1---R3
>
>
> Config from R1:
>
> R1#sh run int virtual-tem 102
> Building configuration...
>
> Current configuration : 74 bytes
> !
> interface Virtual-Template102
> ip address 20.10.13.1 255.255.255.0
> end
>
> R1#sh run int virtual-tem 103
> Building configuration...
>
> Current configuration : 74 bytes
> !
> interface Virtual-Template103
> ip address 20.10.35.1 255.255.255.0
> end
>
> R1#sh run int se 6/0
> Building configuration...
>
> Current configuration : 181 bytes
> !
> interface Serial6/0
> no ip address
> encapsulation frame-relay
> frame-relay interface-dlci 102 ppp Virtual-Template102
> frame-relay interface-dlci 103 ppp Virtual-Template103
> end
>
>
> Config from R2:
>
> R2#sh run int virtual-template 102
> Building configuration...
>
> Current configuration : 74 bytes
> !
> interface Virtual-Template102
> ip address 20.10.13.2 255.255.255.0
> end
>
> R2#sh run int se 4/0
> Building configuration...
>
> Current configuration : 149 bytes
> !
> interface Serial4/0
> no ip address
> encapsulation frame-relay
> serial restart-delay 0
> frame-relay interface-dlci 201 ppp Virtual-Template102
>
> Config from R3:
>
> R3#sh run int virtual-te 103
> Building configuration...
>
> Current configuration : 74 bytes
> !
> interface Virtual-Template103
> ip address 20.10.35.3 255.255.255.0
> end
>
> R3#sh run int se 4/0
> Building configuration...
>
> Current configuration : 125 bytes
> !
> interface Serial4/0
> no ip address
> encapsulation frame-relay
> frame-relay interface-dlci 301 ppp Virtual-Template103
>
> Verification:
>
> R1#ping 20.10.13.2
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 20.10.13.2, timeout is 2 seconds:
> !!!!!
> Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
> R1#ping 20.10.35.3
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 20.10.35.3, timeout is 2 seconds:
> !!!!!
> Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
> R1#sh fram
> R1#sh frame-re
> R1#sh frame-relay pv
> R1#sh frame-relay pvc 102 ?
> 64-bit show frame relay pvc 64bit counter statistics
> | Output modifiers
> <cr>
>
> R1#sh frame-relay pvc 102
>
> PVC Statistics for interface Serial6/0 (Frame Relay DTE)
>
> DLCI = 102, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE =
> Serial6/0
>
> input pkts 19 output pkts 99 in bytes 2332
> out bytes 2064 dropped pkts 0 in pkts dropped 0
>
> out pkts dropped 0 out bytes dropped 0
> in FECN pkts 0 in BECN pkts 0 out FECN pkts 0
>
> out BECN pkts 0 in DE pkts 0 out DE pkts 0
>
> out bcast pkts 0 out bcast bytes 0
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> pvc create time 00:14:52, last time pvc status changed 00:01:34
> Bound to Virtual-Access2 (up, cloned from Virtual-Template102)
> R1#sh frame-relay pvc 103
>
> PVC Statistics for interface Serial6/0 (Frame Relay DTE)
>
> DLCI = 103, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE =
> Serial6/0
>
> input pkts 15 output pkts 118 in bytes 240
> out bytes 2996 dropped pkts 0 in pkts dropped 0
>
> out pkts dropped 0 out bytes dropped 0
> in FECN pkts 0 in BECN pkts 0 out FECN pkts 0
>
> out BECN pkts 0 in DE pkts 0 out DE pkts 0
>
> out bcast pkts 0 out bcast bytes 0
> 5 minute input rate 0 bits/sec, 0 packets/sec
> 5 minute output rate 0 bits/sec, 0 packets/sec
> pvc create time 00:10:07, last time pvc status changed 00:10:07
> Bound to Virtual-Access3 (up, cloned from Virtual-Template103)
> R1#
>
>
> Thanks,
> Sonu
>
>
>
>
>
> -----Original Message-----
> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
> Mohamed Ouamer
> Sent: Tuesday, August 10, 2010 8:06 PM
> To: Marcelo Rosa; ccielab_at_groupstudy.com
> Subject: Re: Frame Relay Interface Configuration problem
>
> Try to configure PPP over Frame Relay.
>
> Hope this help!
>
> Mohamed Ouamer
> http://www.ciscocciebootcamp.com
>
>
>
> 2010/8/10 Marcelo Rosa <MRosa_at_multirede.com.br>
>
>> Sorry. Let me rephrase.
>>
>> 2.1 - Frame Relay Hub&Spoke
>> - Configure frame realy between R1, R3 and R5, using R3 as Hub
>> - All configurations should be done on the physical interface
>> - The connection between R1 and R3 must use the 20.10.13.0/24 network
>> - The connection between R5 and R3 must use the 20.10.35.0/24 network
>> - Do not use secondary ip addresses on R3
>>
>> So, on R3 we have one interface, two IP addresses and two PCVs. I
> cannot
>> use
>> neither secondary addresses nor subinterfaces.
>>
>> Hope I clarified.
>>
>> MR
>>
>> De: masroor ali [mailto:masror.ali_at_gmail.com]
>> Enviada em: terga-feira, 10 de agosto de 2010 11:09
>> Para: Marcelo Rosa; Cisco certification
>> Assunto: Re: Frame Relay Interface Configuration problem
>>
>> i could not understand your question bro,
>> On Tue, Aug 10, 2010 at 6:47 PM, Marcelo Rosa
>> <MRosa_at_multirede.com.br<mailto:MRosa_at_multirede.com.br>> wrote:
>> The question states:
>> Configure FR between R1, R3 and R5
>> PVCs are as follow: R1-R3 (103-301) and R3-R5 (305-503)
>>
>> Link between R1 and R3 should use network 20.10.13.0/24<
>> http://20.10.13.0/24>
>> Link between R5 and R3 should use network 20.10.35.0/24<
>> http://20.10.35.0/24>
>>
>> Configuration only in the Physical interfaces. No secondary ip
> addresses
>> allowed.
>>
>> I4m stuck. As far as I know there4s no way to solve this. Am I wrong?
>>
>> Thks,
>>
>> MR
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>>
> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>>
>>
>>
>>
>>
>>
>> --
>> Regards,
>> Masroor Ali
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>>
> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Tue Aug 10 2010 - 22:23:58 ART