Re: Proactive monitoring of IP SLA with SNMP

You can set up EEM to do this and it will send you an e-mail as soon as it see's "%TRACKING-5-STATE: 1 interface Di1 ip routing Up->Down"

HTHs

On May 12, 2010, at 1:49 PM, eseosa wrote:

> Hi Edouard ,
>
> Since the dialer interface is you primary interface you will be
> interested in its line protocol status .
>
> rather than worrying about a tracking mib you can enable link status
> traps on the dialer interface using the command below:
> int dialer 1
> snmp trap link-status
>
> and configure other snmp related commands(snmp-server community ,
> snmp-server host etc)
>
>
> HTH
>
>
>
>
>
> On 5/12/10, Edouard Zorrilla <ezorrilla_at_tsf.com.pe> wrote:
>> Hello Guys,
>>
>> I hope you can help me with this. Here we have routers with two internet
>> access (DMVPN Network), one is the principal and the other one is the back
>> up.
>>
>> We have set up the router in this way :
>>
>> track 1 interface Dialer1 ip routing
>> ip route 0.0.0.0 0.0.0.0 Dialer1 track 1
>> ip route 0.0.0.0 0.0.0.0 Vlan2 dhcp 100
>>
>> PE0001#CA0269#sh ip int brief | ex down
>> Interface IP-Address OK? Method Status
>> Protocol
>> Dialer1 <Public IP1> YES IPCP up
>> up
>> FastEthernet0 unassigned YES unset up
>> up
>> FastEthernet1 unassigned YES unset up
>> up
>> FastEthernet2 unassigned YES unset up
>> up
>> FastEthernet3 unassigned YES unset up
>> up
>> FastEthernet4 unassigned YES NVRAM up
>> up
>> Tunnel10 172.xx.117.69 YES NVRAM up
>> up
>> Tunnel20 172.yy.117.69 YES NVRAM up
>> up
>> Virtual-Access1 unassigned YES unset up
>> up
>> Vlan1 10.1xy.69.1 YES NVRAM up
>> up
>> Vlan2 <Public IP2> YES DHCP up
>> up
>> PE0001#
>>
>> PE0001#sh inventory
>> NAME: "881", DESCR: "881 chassis.
>>
>>
>> So, if dialer 1 get into a issue, default gateway move to be the secondary
>> line. As soon as "track 1" senses that dialer is in a issue, it will show us
>> a
>> message :
>>
>> %TRACKING-5-STATE: 1 interface Di1 ip routing Up->Down
>>
>> My question is, how can I make that snmp take care of this message ? I want
>> to
>> respond to issues at the first sign of a problem, I mean when primary
>> internet
>> line is down. It would be very good that a Open Source solution (CACTI or
>> Nagios ) could send me one email and show one alarm in monitor tab.
>>
>> But I do not know yet, how can I get the MIB for "track" feature on Cisco
>> IOS.
>> If I guess that If I am able to get the MIB for track command I would be
>> able
>> to monitor my cisco router when the primary line is down.
>>
>> Thanks a lot for your time,
>>
>> Regards
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>>
>>
>>
>>
>>
>
>
> --
> Warm Regards,
>
> Eseosa
> CCIE #23782
> Before God we are all equally wise - and equally foolish.
> Albert Einstein
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Wed May 12 2010 - 13:57:54 ART