Re: L3 etherchannel Dynamips

hey everybody,
just for clarification...
that's a good idea from federico, but that wasn't what i was suggesting
though ...
as tolu rightly suggested, the switch module does not replace all the
functionalities of the 3560
one of those is the l3 etherchannel...
it however supports the l2 etherchannel

it is not a dynamips problem though
On Fri, Feb 19, 2010 at 9:09 PM, Federico Cossu <federico.cossu_at_gmail.com>wrote:

> edmore,
> i think bobola is suggesting you to replace the L3 etherchannel with a
> simple/single L3 interface.
>
> /R
>
>
> 2010/2/19 Edmore Chingwena <chingwenaed_at_gmail.com>
>
> Doesnt work tried it
>>
>> On 19 February 2010 18:54, Bobola Oke <okebobola_at_gmail.com> wrote:
>>
>> > hey edmore,
>> > use no switchport command on the individual interfaces first before
>> > bundling them up
>> > it should work, i think
>> >
>> > but i dont think you're having dynamips problem
>> >
>> >
>> > On Fri, Feb 19, 2010 at 12:37 PM, Tolulope Ogunsina <
>> togunsina_at_gmail.com>wrote:
>> >
>> >> Hi,
>> >> Dynamips does NOT emulate switches or ISRs.
>> >> The NM16ESW module is still NOT a switch :-)
>> >>
>> >> Configuration features of the Etherswitch module are documented here:
>> >>
>> >>
>> >>
>> http://www.cisco.com/en/US/docs/ios/lanswitch/configuration/guide/lsw_enet_switch_net_ps6350_TSD_Products_Configuration_Guide_Chapter.html
>> >>
>> >>
>> >> The NM16ESW does not support layer 3 etherchannels.
>> >>
>> >> On 2/19/10, Edmore Chingwena <chingwenaed_at_gmail.com> wrote:
>> >> > Hi Guys
>> >> >
>> >> > Any help on the issue below I am experiencing any ideas
>> >> >
>> >> > Rack1SW2(config)#int po2
>> >> > Rack1SW2(config-if)#ip address 155.1.108.8 255.255.255.0
>> >> >
>> >> > % IP addresses may not be configured on L2 links.
>> >> >
>> >> > Rack1SW2(config-if)#no switchport
>> >> > Command rejected: not allowed under port channel.
>> >> > Rack1SW2(config-if)#
>> >> >
>> >> > Rack1SW2(config-if)#do show run int port 2
>> >> > Building configuration...
>> >> >
>> >> > Current configuration : 31 bytes
>> >> > !
>> >> > interface Port-channel2
>> >> > end
>> >> >
>> >> > Rack1SW2(config-if)#do show run int fa 1/13
>> >> > Building configuration...
>> >> >
>> >> > Current configuration : 59 bytes
>> >> > !
>> >> > interface FastEthernet1/13
>> >> > channel-group 2 mode on
>> >> > end
>> >> >
>> >> > Rack1SW2(config-if)#do show run int fa 1/14
>> >> > Building configuration...
>> >> >
>> >> > Current configuration : 59 bytes
>> >> > !
>> >> > interface FastEthernet1/14
>> >> > channel-group 2 mode on
>> >> > end
>> >> >
>> >> > Rack1SW2(config-if)#do show run int fa 1/15
>> >> > Building configuration...
>> >> >
>> >> > Current configuration : 59 bytes
>> >> > !
>> >> > interface FastEthernet1/15
>> >> > channel-group 2 mode on
>> >> > end
>> >> >
>> >> > Rack1SW2(config-if)#do show int port 2
>> >> > Port-channel2 is up, line protocol is up
>> >> > Hardware is EtherChannel, address is c20a.0da8.f10f (bia
>> >> c20a.0da8.f10f)
>> >> > MTU 1500 bytes, BW 300000 Kbit/sec, DLY 1000 usec,
>> >> > reliability 255/255, txload 1/255, rxload 1/255
>> >> > Encapsulation ARPA, loopback not set
>> >> > Keepalive set (10 sec)
>> >> > Auto-duplex, Auto-speed
>> >> > Members in this channel: Fa1/13 Fa1/14 Fa1/15
>> >> > ARP type: ARPA, ARP Timeout 04:00:00
>> >> > Last input 00:00:01, output never, output hang never
>> >> > Last clearing of "show interface" counters never
>> >> > Input queue: 39/75/370/0 (size/max/drops/flushes); Total output
>> drops:
>> >> 0
>> >> > Queueing strategy: fifo
>> >> > Output queue: 0/40 (size/max)
>> >> > 5 minute input rate 0 bits/sec, 0 packets/sec
>> >> > 5 minute output rate 0 bits/sec, 0 packets/sec
>> >> > 0 packets input, 0 bytes, 0 no buffer
>> >> > Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
>> >> > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
>> >> > 0 input packets with dribble condition detected
>> >> > 0 packets output, 0 bytes, 0 underruns
>> >> > 0 output errors, 0 collisions, 1 interface resets
>> >> > 0 unknown protocol drops
>> >> > 0 babbles, 0 late collision, 0 deferred
>> >> > 0 lost carrier, 0 no carrier
>> >> > 0 output buffer failures, 0 output buffers swapped out
>> >> > Rack1SW2(config-if)#do show version
>> >> > Cisco IOS Software, 3700 Software (C3725-ADVENTERPRISEK9-M), Version
>> >> > 12.4(15)T10, RELEASE SOFTWARE (fc3)
>> >> > Technical Support: http://www.cisco.com/techsupport
>> >> > Copyright (c) 1986-2009 by Cisco Systems, Inc.
>> >> > Compiled Mon 14-Sep-09 15:53 by prod_rel_team
>> >> >
>> >> >
>> >> > Blogs and organic groups at http://www.ccie.net
>> >> >
>> >> >
>> _______________________________________________________________________
>> >> > Subscription information may be found at:
>> >> > http://www.groupstudy.com/list/CCIELab.html
>> >> >
>> >> >
>> >> >
>> >> >
>> >> >
>> >> >
>> >> >
>> >> >
>> >>
>> >>
>> >> --
>> >> Best Regards,
>> >>
>> >> Tolulope.
>> >>
>> >>
>> >> Blogs and organic groups at http://www.ccie.net
>> >>
>> >> _______________________________________________________________________
>> >> Subscription information may be found at:
>> >> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>>
>>
>>
>>
>>
>
>
> --
> --

Blogs and organic groups at http://www.ccie.net
Received on Fri Feb 19 2010 - 22:25:43 ART