Re: Frame Relay end to end PVC status in GNS3

Hi,

You should add the frame-relay end-to-end keepalive for pvc status on both
routers:

map-class frame-relay FREEK
frame-relay end-to-end keepalive mode bidi

int s0/0
frame-relay class FREEK

same for the subinterface

int s0/0.1
frame-relay interface-dlci 123
class FREEK

HTH,

Ahmed.

On Sat, Feb 13, 2010 at 12:30 PM, Muhammad Anser Khan
<manserkhan_at_gmail.com>wrote:

> Dear Sarad,
>
> Yes, It is a GNS FR Switch Issue. It is working fine If you configure
> router as a FR switch.
>
> Regards,
> Anser
>
> On Sat, Feb 13, 2010 at 9:21 AM, Sarad <tosara_at_gmail.com> wrote:
> > Hi Expert,
> >
> > I am doing some IE expert practice labs there I want to configure two
> > routers with two links ( one frame relay the other point to point serial)
> > using static routes.
> >
> > In the frame relay interface one router is configured as a PTP spoke
> router
> > configuration of this router is as follows
> >
> > Rack1R4#sh run int s0/0.1
> > Building configuration...
> >
> > Current configuration : 115 bytes
> > !
> > interface Serial0/0.1 point-to-point
> > ip address 155.1.0.4 255.255.255.0
> > frame-relay interface-dlci 405
> > end
> >
> > Rack1R4#sh run int s0/0
> > Building configuration...
> >
> > Current configuration : 139 bytes
> > !
> > interface Serial0/0
> > no ip address
> > encapsulation frame-relay
> > shutdown
> > clock rate 2000000
> > cdp enable
> > no frame-relay inverse-arp
> > end
> >
> >
> > the other router is configured as a hub & configuration of that is as
> > follows
> >
> > Rack1R5#sh run int s0/0
> > Building configuration...
> >
> > Current configuration : 286 bytes
> > !
> > interface Serial0/0
> > ip address 155.1.0.5 255.255.255.0
> > encapsulation frame-relay
> > clock rate 2000000
> > cdp enable
> > frame-relay map ip 155.1.0.1 501
> > frame-relay map ip 155.1.0.2 502
> > frame-relay map ip 155.1.0.3 503
> > frame-relay map ip 155.1.0.4 504
> > no frame-relay inverse-arp
> > end
> >
> >
> > Problem I am facing at the movement is when I shut down a main interface
> of
> > frame relay network of any of this router the PVC status of the other end
> > router does not go to inactive.
> >
> > Wonder this is a issue with the GNS or I have missed anything in the
> config.
> >
> > Thanks
> >
> > Sara
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Sat Feb 13 2010 - 12:35:23 ART