RE: Convert SCCP to SIP using CME

In the similar situation, there were two other ways to provision the phone:

1. perform factory reset on the phone (it helped most of the time)
2. if #1 is not helping, move the SIP phone to the vlan that gets it to the
CUCM, configure the SIP phone in CUCM for it, wait for the phone to get the
SIP image, then roll it back to CME. Remove "load" command from the CME
voice register global configuration.

P.S. Are you sure that the image on flash matches the phone platform?

Adel Abouchaev, CCIE# 12037, CISSP, MCSE

Technical Support Engineer
Netmasterclass LLC, Cisco Learning Partner
RFC821: adel_at_netmasterclass.net
E.164: +18886772669
HTTP: www.netmasterclass.net

-----Original Message-----
From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of CCIE
Sent: Sunday, February 07, 2010 3:33 AM
To: 'CCIE'; 'Jeferson Guardia'
Cc: 'groupstudy'
Subject: RE: Convert SCCP to SIP using CME

How I could trigger it to start asking for the SIP files instead of asking
for the SCCP files, i.e.
Make it ask for SIP000AB8CB4BD5.cnf instead of keeping asking for
SEP000AB8CB4BD5.cnf.xml

-----Original Message-----
From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of CCIE
Sent: Sunday, February 07, 2010 1:25 PM
To: 'Jeferson Guardia'
Cc: 'groupstudy'
Subject: RE: Convert SCCP to SIP using CME

I tried it and still that same, but what you mean by manually add the phone
under the CME, do you mean through the voice register pool 1 .etc?

If that what you mean then I already done.

From: Jeferson Guardia [mailto:jefersonf_at_gmail.com]
Sent: Sunday, February 07, 2010 1:23 PM
To: CCIE
Cc: groupstudy
Subject: Re: Convert SCCP to SIP using CME

 Hi mate,

Please try the following

 no upgrade

  no create profile

and then manually add the phone under cme.

Regards,

2010/2/6 CCIE <ccie_at_axizo.com>

Hi Experts

While converting SCCP to SIP using the CME, I read all the previous group
study about that, but I couldn't figure out the right way. It doesn't
convert, any help or advice.

Here what I tried:-

voice service voip

 allow-connections sip to sip

 sip

 registrar server expires max 1200 min 300

!

voice register global

 mode cme

 source-address 177.3.11.1 port 5060

 max-dn 10

 max-pool 5

 load 7960-7940 P003-8-12-00

 authenticate register

 tftp-path flash:

 upgrade

 create profile

tftp-server flash:/P0S3-8-12-00/P003-8-12-00.bin alias P003-8-12-00.bin

tftp-server flash:/P0S3-8-12-00/P003-8-12-00.sbn alias P003-8-12-00.sbn

tftp-server flash:/P0S3-8-12-00/P0S3-8-12-00.loads alias P0S3-8-12-00.loads

tftp-server flash:/P0S3-8-12-00/P0S3-8-12-00.sb2 alias P0S3-8-12-00.sb2

tftp-server flash:/P0S3-8-12-00/OS79XX.TXT alias OS79XX.TXT

voice register dn 1

 number 3002

 name Br2Ph2

 label Br 3002

voice register pool 1

 id mac 000A.B8CB.4BD5

 type 7960

 number 1 dn 1

 dtmf-relay sip-notify

 username br2ph2 password cisco

 codec g711ulaw

telephony-service

max-ephone 1

no ephone 2

Wait more than half hour, nothing happened, then the remove the whole
telephony-service

no telephony-service

and still it keeps looking for the SCCP files,

reloaded the router, and still couldn't covert!!!!

Feb 7 07:02:00.744: TFTP: Looking for CTLSEP000AB8CB4BD5.tlv

Feb 7 07:02:00.808: TFTP: Looking for SEP000AB8CB4BD5.cnf.xml

Feb 7 07:02:00.888: TFTP: Looking for XMLDefault.cnf.xml

Regards,

Amin

Blogs and organic groups at http://www.ccie.net
Received on Sun Feb 07 2010 - 12:01:21 ART