Re: building my own R&S lab

You need to buy 3725's with maxed out dram at 256. This will allow you
to run 12.4T.

Sent from my iPhone

On Dec 30, 2009, at 8:25 PM, Anbu <ksanpu_at_gmail.com> wrote:

> Thanks, if budget is not allowing to go through with 2811 , What is
> the
> recommendation to replace those 2811 to match the version 4
> requirement ?
>
> Regards,
> Anbu
>
> On Wed, Dec 30, 2009 at 12:53 AM, Tyson Scott <tscott_at_ipexpert.com>
> wrote:
>
>> Scuba,
>>
>> To build their rack you will need
>> 6 2811's
>> 6 WIC-2T's
>> 8 DB60 to smart-serial back to backs
>> 2 smart serial to smart-serial back to backs
>> 4 3560's
>> 1 older router that will support 2 or more NM modules. I think a
>> 3640 is a
>> perfect router
>> 2 NM-4T's
>> 1 NM-2E (This is if you want to dual purpose the frame-switch
>> for a
>> backbone router)
>> Lots of 7 ft patch cables.
>>
>> You can then use the 3640 as your frame-switch and your backbone
>> routers.
>> You can use VRF's on the 3640 to make it appear as several backbone
>> routers.
>>
>> That should be all the equipment you need.
>>
>> I am surprised you are not getting direction from NMC as to how to
>> configure
>> their topology. But you will need to contact them to get their
>> frame-relay
>> switch configuration and the BB router configurations. Good Luck
>> in your
>> studies.
>>
>> Regards,
>>
>> Tyson Scott - CCIE #13513 R&S, Security, and SP
>> Technical Instructor - IPexpert, Inc.
>> Mailto: tscott_at_ipexpert.com
>> Telephone: +1.810.326.1444, ext. 208
>>
>>
>>
>> -----Original Message-----
>> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On
>> Behalf Of
>> scuba diver
>> Sent: Tuesday, December 29, 2009 9:33 AM
>> To: Iwan Hoogendoorn; Cisco certification
>> Subject: Re: building my own R&S lab
>>
>> I want to buy 4 3560's and I want to buy 6 2811's with wic-2t's.
>> Can I get
>> the wic-2t's with rj45 ports so I can use cat 6 to plug them into
>> 3560's ?
>> If not, how can I connect them to the 3560's ? Do I have to have
>> smart
>> serial cables ?
>> Scuba
>>
>> On Tue, Dec 29, 2009 at 8:01 AM, scuba diver <scuba1934_at_gmail.com>
>> wrote:
>>
>>> I have NMC Cisco 360 materials and 10k to blow on equipment
>>>
>>>
>>> On Tue, Dec 29, 2009 at 7:25 AM, Iwan Hoogendoorn
>> <iwan_at_ipexpert.com>wrote:
>>>
>>>> What workbook are you going to study?
>>>> If you just want a lab to test certain technologies/topics I would
>>>> keep is small...
>>>>
>>>> I would even advise dynamips/GNS3
>>>>
>>>> If you als going to study a specific workbook (of a vendor) you can
>>>> look into those workbooks ...
>>>> They usually specify what equipment is used ...
>>>>
>>>> --
>>>> Regards,
>>>>
>>>> Iwan Hoogendoorn
>>>> CCIE #13084 (R&S / Security / SP)
>>>> Sr. Support Engineer IPexpert, Inc.
>>>> URL: http://www.IPexpert.com
>>>>
>>>> On Mon, Dec 28, 2009 at 10:11 PM, scuba diver <scuba1934_at_gmail.com>
>>>> wrote:
>>>>> I want to build my own R&S lab. What equipment do I need ?
>>>>>
>>>>> Thanks
>>>>>
>>>>> Scuba
>>>>>
>>>>>
>>>>> Blogs and organic groups at http://www.ccie.net
>>>>>
>>>>>
>> _______________________________________________________________________
 

>>>>> Subscription information may be found at:
>>>>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
 

>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
 

>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
 

> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Wed Dec 30 2009 - 20:52:34 ART