Re: ospf issue

Hi Rick,

I have not erased the configuration before rebooting it.
Further i am geting error
%OSPF: OSPF not enabled on Serial1
wherein I have ip address of the interface in the network statement and in
the interface level command i have entered command
ip ospf network point-to-point
still i am geting the same error

On Tue, Sep 29, 2009 at 9:03 PM, Rick Mur <rmur_at_ipexpert.com> wrote:

> If you ping the other end, no packet loss?
> What kind of link is between the 2 routers?
> Could you post the OSPF and interface configuration of both routers.
>
> Have you erased the configs of both routers and reloaded them both and then
> reconfigured this?
>
> --
>
> Regards,
>
> Rick Mur
> CCIE2 #21946 (R&S / Service Provider)
> Sr. Support Engineer  IPexpert, Inc.
> URL: http://www.IPexpert.com <http://www.ipexpert.com/>
>
>
> On Tue, Sep 29, 2009 at 4:50 PM, aashish kapoor <operationccie_at_gmail.com
> > wrote:
>
>> Thanks but I have checked all of them they were fine
>> I have just got the same network statement in the new process and it is
>> working
>>
>> Regards
>> Aashish Kapoor
>>
>> On Tue, Sep 29, 2009 at 8:13 PM, Divin Mathew John <divinjohn_at_gmail.com
>> >wrote:
>>
>> > Check the following
>> >
>> > 1) Area configured on both sides shud match
>> > 2) Stub flag shud match
>> > 3) Timers shud Match
>> > 4) Dr/BDR Election type shud match
>> > 5) MTU shud Match
>> >
>> >
>> > On Tue, Sep 29, 2009 at 8:04 PM, aashish kapoor <
>> operationccie_at_gmail.com
>> > > wrote:
>> >
>> >> Hi Group,
>> >>
>> >> I have faced one issue with ospf.
>> >> R1 ------ R2
>> >> running point to point ospf were not forming ospf adjacency
>> >> I have checked every possible cause and turned debug on only message is
>> >> got
>> >> was that the far end in dead
>> >> I have restarted ospf process..... have remove and added the network
>> >> statement again but it did not worked.
>> >>
>> >> Then I have removed network statement from the existing ospf process
>> and
>> >> created a new ospf process and added this statement into it. It worked
>> and
>> >> formed adjacency.
>> >>
>> >> Please advise what could be possible cause.
>> >>
>> >> Regards
>> >> Aashish Kapoor
>> >>
>> >>
>> >> Blogs and organic groups at http://www.ccie.net
>> >>
>> >> _______________________________________________________________________
>> >> Subscription information may be found at:
>> >> http://www.groupstudy.com/list/CCIELab.html
>> >>
>> >>
>> >>
>> >>
>> >>
>> >>
>> >>
>> >>
>> >
>> >
>> > --
>> >
>> > Sent from Karnataka, India
>> > Vilhjalmur Stefansson <http://www.quotationspage.com/quote/1459.html>
>> -
>> > "What is the difference between unethical and ethical advertising?
>> Unethical
>> > advertising uses...
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Tue Sep 29 2009 - 21:44:29 ART