RE: Interface in multiple OSPF prcesses having multiple areas?

Can you use debugs during OEQ? ;)

-----Original Message-----
From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
Mark Matters
Sent: 11 September 2009 02:04 AM
To: CCIE League
Cc: CCIEGS
Subject: Re: Interface in multiple OSPF prcesses having multiple areas?

That is interesting. Did you run any debugs to see what OSPF is doing?
What happens when you clear ip os pro?

On Wed, Sep 9, 2009 at 6:12 PM, CCIE League <ccieleague_at_ymail.com>
wrote:

> Experts,
>
> Can an ospf interface participate in more than one process having
multiple
> area?
>
>
>
> I tried to do do this, strange output... see "sh ip ospf int br"
output
> where it says PID =3 /AREA=2 but i configured ID=3/AREA=0
>
>
> In think answer is no? Any comments....
>
>
> Ta,
>
>
>
> -----------------------------------
> NEW#
> NEW#
> NEW#
> NEW#s
> Sep 9 23:06:11.466: %SYS-5-CONFIG_I: Configured from console by
console
> NEW#sro
> router ospf 1
> log-adjacency-changes
> network 1.1.1.1 0.0.0.0 area 1
> router ospf 2
> router-id 1.1.1.2
> log-adjacency-changes
> network 1.1.1.1 0.0.0.0 area 2
> router ospf 3
> router-id 1.1.1.3
> log-adjacency-changes
> network 1.1.1.1 0.0.0.0 area 0
> alias exec sro show running-config | section router ospf
> NEW#
> NEW#
> NEW#
>
> NEW#sh ip int brie
> Interface IP-Address OK? Method Status
> Protocol
> FastEthernet0/1 1.1.1.1 YES manual up
> up
> NEW#
> NEW#
>
> NEW#sh ip ospf int f0/1
> FastEthernet0/1 is up, line protocol is up
> Internet Address 1.1.1.1/24, Area 2
> Process ID 3, Router ID 1.1.1.3, Network Type BROADCAST, Cost: 1
> Enabled by interface config, including secondary ip addresses
> Transmit Delay is 1 sec, State DR, Priority 1
> Designated Router (ID) 1.1.1.3, Interface address 1.1.1.1
> No backup designated router on this network
> Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
> oob-resync timeout 40
> Hello due in 00:00:05
> Supports Link-local Signaling (LLS)
> Index 1/1, flood queue length 0
> Next 0x0(0)/0x0(0)
> Last flood scan length is 0, maximum is 0
> Last flood scan time is 0 msec, maximum is 0 msec
> Neighbor Count is 0, Adjacent neighbor count is 0
> Suppress hello for 0 neighbor(s)
>
> NEW#
> NEW#
> NEW#
> NEW#
> NEW#sh ip osfp int br
> Interface PID Area IP Address/Mask Cost State Nbrs
F/C
> Fa0/1 3 2 1.1.1.1/24 1 DR 0/0
> NEW#
> NEW#
> ---------------------------------------------------------------------
>
>
> Blogs and organic groups at http://www.ccie.net
>
>
Received on Fri Sep 11 2009 - 12:15:43 ART