Re: PPPoE with IPv6

Hey Iwan,

I was using 2x 2811 running 12.4(24)T1 code. I also tried previously on the
same hardware using 12.4(3a) code. Rick also tried a dynamips shot at it
with the same results on 12.4T code.

On Wed, Sep 2, 2009 at 5:48 AM, Iwan Hoogendoorn <iwan_at_ipexpert.com> wrote:

> Joe,
>
> I am going to rebuild this in dynamips this evening.
> What IOS featureset did you use and on what platform are you testing this?
> Maybe you can specify the whole IOS image filename...
>
> I am also interested in getting this working.
>
> --
> Regards,
>
> Iwan Hoogendoorn
> CCIE #13084 (R&S / Security / SP)
> Sr. Support Engineer  IPexpert, Inc.
> URL: http://www.IPexpert.com
>
>
> On Wed, Sep 2, 2009 at 8:10 AM, Joe Astorino<jastorino_at_ipexpert.com>
> wrote:
> > Has anybody successfully set this up?
> >
> > Basically, on the PPPoE server side, when I assign my ipv6 address to the
> > virtual-template interface you can see it , but the router never adds a
> > route for it in the routing table. On the client end of the PPPoE things
> > seem to work fine using the dialer interface. Interestingly enough, I
> see
> > IPv6CP negotiating OK in the debugs, and I can actually see the
> link-local
> > address of the other side in "show ipv6 neighbor" but no ping to the
> other
> > side global address. I've even tried ipv6 unnumbered with no luck.
> >
> > Also, it works totally fine for IPv4...I have enabled ipv6
> unicast-routing
> > of course, and also ipv6 cef just in case. I am running 12.4(24)T1 and
> have
> > also tried this on 12.4(3a)
> >
> > basically I have below:
> >
> > Server
> > ----------
> >
> > vpdn enable
> > bba-group pppoe global
> > virtual-template 1
> >
> > interface FastEthernet0/0
> > no ip address
> > duplex auto
> > speed auto
> > pppoe enable group global
> >
> > interface Virtual-Template1
> > mtu 1492
> > ip address 141.41.67.6 255.255.255.0
> > ipv6 address 2001:0:0:67::6/64
> > ipv6 enable
> >
> >
> > Client
> > --------
> >
> > interface FastEthernet0/0
> > no ip address
> > duplex auto
> > speed auto
> > pppoe enable group global
> > pppoe-client dial-pool-number 1
> >
> > interface Dialer1
> > mtu 1492
> > ip address dhcp
> > encapsulation ppp
> > dialer pool 1
> > dialer idle-timeout 0
> > dialer persistent
> > ipv6 address FE80::7 link-local
> > ipv6 address 2001:0:0:67::7/64
> > ipv6 enable
> >
> >
> > so check this out...
> >
> > R6(config-if)#do sh run int virtual-template1
> > Building configuration...
> >
> > Current configuration : 128 bytes
> > !
> > interface Virtual-Template1
> > mtu 1492
> > ip address 141.41.67.6 255.255.255.0
> > ipv6 address 2001:0:0:67::6/64
> > ipv6 enable
> > end
> >
> > R6(config-if)#do sh ipv6 route
> > IPv6 Routing Table - Default - 10 entries
> > Codes: C - Connected, L - Local, S - Static, U - Per-user Static route
> > B - BGP, M - MIPv6, R - RIP, I1 - ISIS L1
> > I2 - ISIS L2, IA - ISIS interarea, IS - ISIS summary, D - EIGRP
> > EX - EIGRP external
> > O - OSPF Intra, OI - OSPF Inter, OE1 - OSPF ext 1, OE2 - OSPF ext 2
> > ON1 - OSPF NSSA ext 1, ON2 - OSPF NSSA ext 2
> > R 2001::2/128 [120/2]
> > via FE80::2, Serial0/1/0
> > R 2001::5/128 [120/3]
> > via FE80::2, Serial0/1/0
> > LC 2001::6/128 [0/0]
> > via Loopback6, receive
> > C 2001::256:0/125 [0/0]
> > via Serial0/1/0, directly connected
> > L 2001::256:6/128 [0/0]
> > via Serial0/1/0, receive
> > C 2001:0:0:69::/64 [0/0]
> > via Serial0/2/0, directly connected
> > L 2001:0:0:69::6/128 [0/0]
> > via Serial0/2/0, receive
> > C 2001:0:0:70::/64 [0/0]
> > via Serial0/2/1, directly connected
> > L 2001:0:0:70::6/128 [0/0]
> > via Serial0/2/1, receive
> > L FF00::/8 [0/0]
> > via Null0, receive
> >
> > R6(config-if)#do ping 2001:0:0:67::7
> >
> > Type escape sequence to abort.
> > Sending 5, 100-byte ICMP Echos to 2001:0:0:67::7, timeout is 2 seconds:
> >
> > % No valid route for destination
> > Success rate is 0 percent (0/1)
> >
> > --
> > Regards,
> >
> > Joe Astorino - CCIE #24347 R&S
> > Technical Instructor - IPexpert, Inc.
> > Cell: +1.586.212.6107
> > Fax: +1.810.454.0130
> > Mailto: jastorino_at_ipexpert.com
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> >
> >
> >
> >
> >
> >
>
>
>
> --
> Regards,
>
> Iwan Hoogendoorn
> CCIE #13084 (R&S / Security / SP)
> Sr. Support Engineer  IPexpert, Inc.
> URL: http://www.IPexpert.com
>

--
Regards,
Joe Astorino - CCIE #24347 R&S
Technical Instructor - IPexpert, Inc.
Cell: +1.586.212.6107
Fax: +1.810.454.0130
Mailto:  jastorino_at_ipexpert.com
Blogs and organic groups at http://www.ccie.net