Re: OSPF Virtual Link

Hi Ryan and Divin, tanks fir ur responses. I got it fixed by doing "debug ip
os hello" . I noticed that as R1 was also connected to another router via
another FR interface, the hello from R1 was originated by its other FR int
as the inverse arp was not disbaled on this interface. Its fixed now. Thanks
again.

thanks
Syed

On Wed, May 27, 2009 at 12:14 AM, Divin Mathew John <divinjohn_at_gmail.com>wrote:

> which link is in Area 0?
> Thanking You
>
> Yours Sincerely
>
> Divin Mathew John
> divinjohn_at_gmail.com
> divin_at_dide3d.com
> http://www.dide3d.com
> +91 9945430983
> +91 9846697191
> +974 5008916
> PGP PUBLIC KEY BLOCK @ http://www.dide3d.com/divin_Public_PGP_key.txt
>
>
>
> On Wed, May 27, 2009 at 2:35 AM, Syed Ali <testcricket_at_gmail.com> wrote:
>
>> Hi Ryan,
>> Please see below the related info:
>>
>>
>>
>> R1#sh ip os vir
>> Virtual Link OSPF_VL4 to router 2.2.2.2 is up
>> Run as demand circuit
>> DoNotAge LSA allowed.
>> Transit area 5, via interface Serial0/1, Cost of using 64
>> Transmit Delay is 1 sec, State POINT_TO_POINT,
>> Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
>> Hello due in 00:00:06
>> Adjacency State FULL (Hello suppressed)
>> Index 2/3, retransmission queue length 0, number of retransmission 0
>> First 0x0(0)/0x0(0) Next 0x0(0)/0x0(0)
>> Last retransmission scan length is 0, maximum is 0
>> Last retransmission scan time is 0 msec, maximum is 0 msec
>> R1#
>> router ospf 1
>> router-id 1.1.1.1
>> ispf
>> log-adjacency-changes
>> area 5 virtual-link 2.2.2.2
>> network 5.5.12.1 0.0.0.0 area 5
>> neighbor 5.5.55.2
>> !
>>
>> ========================================================================================
>>
>> R2#sh ip os vir
>> Virtual Link OSPF_VL0 to router 1.1.1.1 is up
>> Run as demand circuit
>> DoNotAge LSA allowed.
>> Transit area 5, via interface Serial0/0, Cost of using 64
>> Transmit Delay is 1 sec, State POINT_TO_POINT,
>> Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
>> Hello due in 00:00:04
>> Adjacency State INIT
>> Index 0/0, retransmission queue length 0, number of retransmission 0
>> First 0x0(0)/0x0(0) Next 0x0(0)/0x0(0)
>> Last retransmission scan length is 0, maximum is 0
>> Last retransmission scan time is 0 msec, maximum is 0 msec
>> R2#
>> router ospf 1
>> router-id 2.2.2.2
>> log-adjacency-changes
>> area 5 virtual-link 1.1.1.1
>> network 5.5.55.2 0.0.0.0 area 5
>> !
>>
>> thanks
>> Syed
>>
>>
>>
>>
>>
>> On Tue, May 26, 2009 at 11:50 PM, Ryan West <rwest_at_zyedge.com> wrote:
>>
>> > Syed,
>> >
>> > To better assist, please post 's ip os nei', 's run | s r o', and 's run
>> > int lo 0'
>> >
>> > Thanks,
>> >
>> > -ryan
>> >
>> > -----Original Message-----
>> > From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
>> > Syed Ali
>> > Sent: Tuesday, May 26, 2009 4:44 PM
>> > To: Cisco certification
>> > Subject: OSPF Virtual Link
>> >
>> > Hi Experts,
>> > I have a virtual link between two routers. One side is
>> adj
>> > is FULL but the other side shows INIT. Each side is configured with the
>> > remote side router id as the virtual link peer but no success. Can
>> anyone
>> > help?
>> >
>> > thanks
>> > Syed
>> >
>> >
>> > Blogs and organic groups at http://www.ccie.net
>> >
>> > _______________________________________________________________________
>> > Subscription information may be found at:
>> > http://www.groupstudy.com/list/CCIELab.html
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Wed May 27 2009 - 00:23:37 ART