Re: Unable to Write-Memory in 4006 Cat OS

I've changed the config-register to 0x2.

As I Understand this is the default .

and this will still launch the CONFIG_FILE variable = bootflash:switch.cfg

anyway as darby said before - when you write a command in the 4006.
it is commited, no need to do write-memory.

So I just needed to change the 0x2.

Thanks, Darby and Radio.

On 4/29/09, Radioactive Frog <pbhatkoti_at_gmail.com> wrote:
>
> let us know dude...
>
> -frog
>
> 2009/4/27 WW)W WWWW W <eshedalonie_at_gmail.com>
>
>> Darby,
>>
>> It Says to you
>> File bootflash:switch.cfg can not be opened (file not found)
>>
>>
>> When you Do -> copy flash config
>>
>> It asks you to put the file in bootflash:
>> and then it says the name of the file.
>>
>> so I've named it as current.cfg
>>
>> When I did dir
>>
>> I Saw the file in bootflash:current.cfg
>>
>> anyway,
>>
>> the config-register 0x2 Looks good
>>
>>
http://www.cisco.com/en/US/docs/routers/access/4000/hardware/installation/gui
>>
de/vconfig.html<http://www.cisco.com/en/US/docs/routers/access/4000/hardware/
installation/gui%0Ade/vconfig.html>
>>
>> I Will try that, Thanks Radioactive Frog.
>>
>>
>> On 4/26/09, Darby Weaver <ccie.weaver_at_gmail.com> wrote:
>> >
>> > It's legacy.
>> >
>> > When you type a command - it is committed.
>> >
>> > You have two commands that rock:
>> >
>> > sh config - and save it out to text. - The commands that are manually
>> > entered and non-default.
>> >
>> > sh config all - all the commands - both default and the ones manually
>> > entered. Careful if you are a tree-hugger...
>> >
>> > 4006-1> (enable) sh boot
>> > BOOT variable = bootflash:cat4000-k8.8-4-7-GLX.bin,1;
>> > CONFIG_FILE variable = bootflash:switch.cfg
>> > Configuration register is 0x2102
>> > ignore-config: disabled
>> > auto-config: non-recurring
>> > console baud: 9600
>> > boot: image specified by the boot system commands
>> >
>> >
>> > 4006-1> (enable) copy bootflash:switch.cfg tftp
>> > File bootflash:switch.cfg does not exist
>> > Failed to copy from bootflash:switch.cfg to tftp
>> >
>> > -4006-1> (enable) sh file switch.cfg
>> > error = -9
>> > File bootflash:switch.cfg can not be opened (file not found)
>> > -4006-1> (enable) sh file bootflash:switch.cfg
>> > error = -9
>> > File bootflash:switch.cfg can not be opened (file not found)
>> > -4006-1> (enable)
>> >
>> > Nice try.
>> >
>> > See you can't read the file because it is in use and running as I recall
>> > and as you can see above - it just won't let you.
>> >
>> > It's not the typical IOS... Still CatOS.
>> >
>> > Hope this helps - But I think you already tried what I just displayed.
>> >
>> >
>> >
>> >
>> >
>> > 2009/4/26 W W)W W W W W W <eshedalonie_at_gmail.com>
>> >
>> >> Main_4006> (enable) write memory
>> >> This command is available only in text configuration mode.
>> >> Main_4006> (enable)
>> >>
>> >> Instead I have used
>> >>
>> >> copy flash config
>> >>
>> >> set boot auto-config bootflash:current.cfg
>> >>
>> >> Does anyone have a clue why the switch doesn't allow me to do
>> >> write-memory
>> >> ?
>> >>
>> >>
>> >> Blogs and organic groups at http://www.ccie.net
>> >>
>> >> _______________________________________________________________________
>> >> Subscription information may be found at:
>> >> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net
Received on Wed Apr 29 2009 - 09:41:42 ART