Re: FREEK

Thanks for citing this config example! This helps in understanding what is
going on.

On Sat, Apr 18, 2009 at 11:20 PM, Ryan West <rwest_at_zyedge.com> wrote:

> You answered his question, but the actual configuration example is a bit
> further down and pretty much mirrors the example he gave:
>
>
> http://www.cisco.com/en/US/docs/ios/wan/configuration/guide/wan_cfg_frm_rly_ps6350_TSD_Products_Configuration_Guide_Chapter.html#wp1003556
>
> To the OP, you just need mode reply enabled.
>
>
> -ryan
>
> -----Original Message-----
> From: nobody_at_groupstudy.com [mailto:nobody_at_groupstudy.com] On Behalf Of
> ALL From_NJ
> Sent: Saturday, April 18, 2009 8:12 PM
> To: nowy1981
> Cc: Cisco certification
> Subject: Re: FREEK
>
> Hello and good evening. I hope all is well.
>
> A few options related to this technology, here is a good link which
> discusses these (watch the ugly word wrap):
>
>
> http://www.cisco.com/en/US/docs/ios/wan/configuration/guide/wan_cfg_frm_rly_ps6350_TSD_Products_Configuration_Guide_Chapter.html#wp1001904
>
> FREEK has to be configured on both ends. A little 'digging' from this
> link:
>
> *
> **You must configure both ends of a VC to send keepalives. If one end is
> configured as bidirectional, the other end must also be configured as
> bidirectional. If one end is configured as request, the other end must be
> configured as reply or passive-reply. If one end is configured as reply or
> passive-reply, the other end must be configured as request *
>
> HTH,
>
> Andrew Lee Lissitz
>
>
>
> 2009/4/18 nowy1981 <freemaxis_at_gmail.com>
>
> > If I configured following options on the REQUEST side
> >
> > map-class frame-relay FREEK
> > frame-relay end-to-end keepalive mode request
> > frame-relay end-to-end keepalive timer send 5
> > frame-relay end-to-end keepalive event-window send 10
> > frame-relay end-to-end keepalive error-threshold send 8
> >
> > do I have to reflect it on the REPLY router?
> >
> > map-class frame-relay FREEK
> > frame-relay end-to-end keepalive mode reply
> > frame-relay end-to-end keepalive timer recv 5
> > frame-relay end-to-end keepalive event-window recv 10
> > frame-relay end-to-end keepalive error-threshold recv 8
> >
> >
> > I mean question that specify only that router should poll every 5 sec
> with
> > event window of 10 and an error threshold of 8, no details about reply
> side.
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> >
> >
> >
> >
> >
> >
>
>
> --
> Andrew Lee Lissitz
> all.from.nj_at_gmail.com
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>
>

-- 
Andrew Lee Lissitz
all.from.nj_at_gmail.com
Blogs and organic groups at http://www.ccie.net