From: Danshtr (danshtr@gmail.com)
Date: Sat Mar 07 2009 - 12:20:13 ARST
It is supported, but it got nothing to do with dynamips.
One of the emulated routers is a cellmode ATM switch with an ATM cell mode
switch configuration.
Look at the initial configuration for the dynamips labs.
Best regards,
Dan
On Sat, Mar 7, 2009 at 4:14 PM, backbone systems <backbone.systems@gmail.com
> wrote:
> Can anyone please confirm if the following is possible on dynamips,
>
> interface ATM3/0.1 tag-switching
> ip address 150.1.19.1
> tag-switching atm control-vc 40 40
> tag-switching ip
>
>
> interface ATM3/0.1 tag-switching
> ip address 150.1.19.2
> tag-switching atm control-vc 40 40
> tag-switching ip
>
> As far as i know cell made switching is not supported on dynamips?????
> i can not run this command
>
> interface ATM3/0.1 tag-switching
>
> Please confirm???
>
> I was using those interfaces as normal and running mpls ip on the atm
> interface which is frame mode ??? am i right.
>
> On Sat, Mar 7, 2009 at 2:19 PM, Nitin Venugopal <nitinsworld@gmail.com>
> wrote:
> > Hi,
> >
> > You have to define in the subinterface for cell-mode , if it will be a
> > point to point , multipoint , mpls or tag-switching
> >
> > Below will be if its for MPLS
> >
> > interface ATM3/0.1 tag-switching
> > ip address 150.1.19.1
> > tag-switching atm control-vc 40 40
> > tag-switching ip
> >
> >
> > interface ATM3/0.1 tag-switching
> > ip address 150.1.19.2
> > tag-switching atm control-vc 40 40
> > tag-switching ip
> >
> >
> > Regds
> > Nitin
> >
> > On Sat, Mar 7, 2009 at 12:07 PM, Vignesh Sethuraman
> > <sethuvignesh@gmail.com>wrote:
> >
> >> Hello,
> >>
> >> I was configuring basic atm configuration between 2 routers connected
> via
> >> ATM switch in my 4 GB Ram laptop running WindowsXP.
> >>
> >> R1(3/0) ------ 1/0 (ATM SW) 2/0 ------(3/0) R2
> >>
> >> I am unable to ping R1 to R2
> >>
> >> R1:
> >> interface ATM3/0
> >> ip address 150.1.19.1 255.255.255.0
> >> no atm enable-ilmi-trap
> >> no clns route-cache
> >> pvc 0/102
> >> protocol ip 150.1.19.2 broadcast
> >>
> >> R2:
> >> interface ATM3/0
> >> ip address 150.1.19.2 255.255.255.0
> >> no atm enable-ilmi-trap
> >> no clns route-cache
> >> pvc 0/102
> >> protocol ip 150.1.19.1 broadcast
> >>
> >> R1#p 150.1.19.2
> >> Type escape sequence to abort.
> >> Sending 5, 100-byte ICMP Echos to 150.1.19.2, timeout is 2 seconds:
> >> .....
> >> Success rate is 0 percent (0/5)
> >> R1#
> >> I have started my Cell mode atm switch. But i did not do any mappings on
> >> the
> >> ATM switch. Do we need to configure mappings on the ATM switch as like
> the
> >> FRSW. I am using InternetworkExpert .net file.
> >>
> >> And also CPU process is showing 100% even if i choose the best idlepc
> shown
> >> in the GNS.
> >>
> >> Could you pleas help me to resolve this issue.
> >>
> >> Thanks,
> >> Vignesh
> >>
> >>
> >> Blogs and organic groups at http://www.ccie.net
> >>
> >> _______________________________________________________________________
> >> Subscription information may be found at:
> >> http://www.groupstudy.com/list/CCIELab.html
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Mon Apr 06 2009 - 06:44:04 ART