From: backbone systems (backbone.systems@gmail.com)
Date: Sat Mar 07 2009 - 12:14:37 ARST
Can anyone please confirm if the following is possible on dynamips,
interface ATM3/0.1 tag-switching
ip address 150.1.19.1
tag-switching atm control-vc 40 40
tag-switching ip
interface ATM3/0.1 tag-switching
ip address 150.1.19.2
tag-switching atm control-vc 40 40
tag-switching ip
As far as i know cell made switching is not supported on dynamips?????
i can not run this command
interface ATM3/0.1 tag-switching
Please confirm???
I was using those interfaces as normal and running mpls ip on the atm
interface which is frame mode ??? am i right.
On Sat, Mar 7, 2009 at 2:19 PM, Nitin Venugopal <nitinsworld@gmail.com> wrote:
> Hi,
>
> You have to define in the subinterface for cell-mode , if it will be a
> point to point , multipoint , mpls or tag-switching
>
> Below will be if its for MPLS
>
> interface ATM3/0.1 tag-switching
> ip address 150.1.19.1
> tag-switching atm control-vc 40 40
> tag-switching ip
>
>
> interface ATM3/0.1 tag-switching
> ip address 150.1.19.2
> tag-switching atm control-vc 40 40
> tag-switching ip
>
>
> Regds
> Nitin
>
> On Sat, Mar 7, 2009 at 12:07 PM, Vignesh Sethuraman
> <sethuvignesh@gmail.com>wrote:
>
>> Hello,
>>
>> I was configuring basic atm configuration between 2 routers connected via
>> ATM switch in my 4 GB Ram laptop running WindowsXP.
>>
>> R1(3/0) ------ 1/0 (ATM SW) 2/0 ------(3/0) R2
>>
>> I am unable to ping R1 to R2
>>
>> R1:
>> interface ATM3/0
>> ip address 150.1.19.1 255.255.255.0
>> no atm enable-ilmi-trap
>> no clns route-cache
>> pvc 0/102
>> protocol ip 150.1.19.2 broadcast
>>
>> R2:
>> interface ATM3/0
>> ip address 150.1.19.2 255.255.255.0
>> no atm enable-ilmi-trap
>> no clns route-cache
>> pvc 0/102
>> protocol ip 150.1.19.1 broadcast
>>
>> R1#p 150.1.19.2
>> Type escape sequence to abort.
>> Sending 5, 100-byte ICMP Echos to 150.1.19.2, timeout is 2 seconds:
>> .....
>> Success rate is 0 percent (0/5)
>> R1#
>> I have started my Cell mode atm switch. But i did not do any mappings on
>> the
>> ATM switch. Do we need to configure mappings on the ATM switch as like the
>> FRSW. I am using InternetworkExpert .net file.
>>
>> And also CPU process is showing 100% even if i choose the best idlepc shown
>> in the GNS.
>>
>> Could you pleas help me to resolve this issue.
>>
>> Thanks,
>> Vignesh
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Mon Apr 06 2009 - 06:44:04 ART