Re: CCIE SP Basic Configuration - InternetworkExpert .net file

From: Ioan Branet (ioan.branet@gmail.com)
Date: Sat Mar 07 2009 - 10:11:52 ARST

Hello,

Try to see the .net file for atm interface mappings, for me the .net file
shows that int AM4/0 from R1 goues to ATM switch and int ATM4/0 from R2 goes
to ATM switch

For me it works the following configuration:

Rack1R1#sri atm4/0
Building configuration...

Current configuration : 250 bytes
!
interface ATM4/0
description Put Cell Mode MPLS Configs Here
ip address 150.1.12.1 255.255.255.0
ip router isis
no atm enable-ilmi-trap
pvc 0/102
 protocol ip 150.1.12.2 broadcast
 protocol clns 49.0024.0000.0000.0002.00 broadcast

Rack1R2#sri atm4/0
Building configuration...

Current configuration : 255 bytes
!
interface ATM4/0
description Put Cell Mode MPLS Configs Here
ip address 150.1.12.2 255.255.255.0
ip router isis
no atm enable-ilmi-trap
pvc 0/201
 protocol ip 150.1.12.1 broadcast
 protocol clns 49.0013.0000.0000.0000.0001.00 broadcast
!
end

Rack1R1#sh clns is-neighbors

System Id Interface State Type Priority Circuit Id Format
Rack1R2 AT4/0 Up L2 64 Rack1R2.02 Phase V
Rack1R3 Se2/1 Up L1 0 00 Phase V
Rack1R1#

 [[Router R1]]
  model = 7200
  autostart = false
  slot0 = PA-C7200-IO-FE
  slot2 = PA-4T
  slot3 = PA-A1
  slot4 = PA-A1
  F0/0 = SW1 F1/1
  S2/0 = FRSW 1
  A3/0 = CellModeATM A1/0
* A4/0 = A1 1
*

 [[Router R2]]
  model = 7200
  autostart = false
  slot0 = PA-C7200-IO-FE
  slot2 = PA-4T
  slot3 = PA-A1
  slot4 = PA-A1
  F0/0 = SW1 F1/2
  S2/0 = FRSW 2
  A3/0 = CellModeATM A2/0
* A4/0 = A1 2*

On Sat, Mar 7, 2009 at 10:07 AM, Vignesh Sethuraman
<sethuvignesh@gmail.com>wrote:

> Hello,
>
> I was configuring basic atm configuration between 2 routers connected via
> ATM switch in my 4 GB Ram laptop running WindowsXP.
>
> R1(3/0) ------ 1/0 (ATM SW) 2/0 ------(3/0) R2
>
> I am unable to ping R1 to R2
>
> R1:
> interface ATM3/0
> ip address 150.1.19.1 255.255.255.0
> no atm enable-ilmi-trap
> no clns route-cache
> pvc 0/102
> protocol ip 150.1.19.2 broadcast
>
> R2:
> interface ATM3/0
> ip address 150.1.19.2 255.255.255.0
> no atm enable-ilmi-trap
> no clns route-cache
> pvc 0/102
> protocol ip 150.1.19.1 broadcast
>
> R1#p 150.1.19.2
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 150.1.19.2, timeout is 2 seconds:
> .....
> Success rate is 0 percent (0/5)
> R1#
> I have started my Cell mode atm switch. But i did not do any mappings on
> the
> ATM switch. Do we need to configure mappings on the ATM switch as like the
> FRSW. I am using InternetworkExpert .net file.
>
> And also CPU process is showing 100% even if i choose the best idlepc shown
> in the GNS.
>
> Could you pleas help me to resolve this issue.
>
> Thanks,
> Vignesh
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
>
>
>
> 

-- 
Ioan Branet
CCIE #23474 R&S

Blogs and organic groups at http://www.ccie.net

This archive was generated by hypermail 2.1.4 : Mon Apr 06 2009 - 06:44:04 ART