From: Ravi Singh (way2ccie@googlemail.com)
Date: Fri Feb 06 2009 - 12:54:22 ARST
Well .. The document really has everything you need to know. Anyhow , I will
try to clear your doubts in simpler terms .
RSTP does not require any additional configuration by itself , though the
features which make it RSTP , obviously need to be configured . For example
you won't explicitly enable RSTP but you would enable portfast, uplinkfast
or backbonefast with their relevant commands.
RSTP is called Rapid only because of these features hence these are a part
of RSTP.
coming to your questions
1) should STP be disabled on edge ports all together ? As a good practice ,
Yes. Your explanation has the answer "If RSTP is not disabled on edge ports,
convergence times will be excessive for packets traversing those ports " .
There is no use for STP to be enabled to a port connected to a PC. so why
wait for 30 seconds for the port to realise not to run STP on it.
2)What is the configuration to explicitly configure RSTP link types? Again
your explanation has the answer "A port that operates in fullduplex is
assumed to be point-to-point, while a half-duplex port is considered as a
shared port by default". So change the duplex settings explicitly and you
can change the link type .
HTH, and I definitely stand to be corrected so anyone with any comments is
most welcome.
Regards,
Ravi
On Fri, Feb 6, 2009 at 2:37 PM, operator sid <ccie1@live.co.uk> wrote:
>
> I have read it,and unfortunately its not a good document, i was hoping
> someone could explain better...
>
>
> ________________________________
> > Date: Fri, 6 Feb 2009 14:09:48 +0000
> > Subject: Re: Understanding RSTP - Please can someone explain this?
> > From: way2ccie@googlemail.com
> > To: ccie1@live.co.uk
> > CC: ccielab@groupstudy.com
> >
> > This might help if you have not read it before
> >
> >
> >
> >
> http://www.cisco.com/en/US/tech/tk389/tk621/technologies_white_paper09186a0080094cfa.shtml
> >
> >
> >
> > Ravi
> >
> >
> > On Fri, Feb 6, 2009 at 12:25 PM, operator sid> wrote:
> >
> > Hi Group
> >
> >
> >
> > I am still confused about how RSTP is implemented. From what i understand
> the major difference is that STP
> >
> >
> > used Timers for Loop prevention whereas RSTP coordinates between
> neighbors via messages (proposal/aggreement) to turn on links
> >
> > more quickly after topology changes and is "timer free".
> >
> >
> >
> >
> > However, I have not noticed any difference in the configuration from the
> legacy STP
> >
> > configurations and the RSTP configuration on cisco devices. Or are there
> any differences??
> >
> >
> >
> > I have read in documentation that RSTP natively includes features
> >
> > like UplinkFast, BackboneFast and PortFast. So are these features now
> > obsolete
> > and not needed to be configured if you are running RSTP.
> > (Although i have seen Portfast still configured along with RSTP on many
> > switches)
> >
> >
> >
> >
> > Also can someone explain the below Points from Cisco Documentation
> >
> >
> >
> > 1) should STP be disabled on edge ports all together as suggested below?
> >
> >
> >
> > "STP edge ports are bridge ports that do not need STP enabled, where loop
> protection is not needed out
> >
> >
> > of that port or an STP neighbor does not exist out of that port. For
> RSTP, it is important to disable STP
> >
> > on edge ports, which are typically front-side Ethernet ports, using the
> command bridge
> >
> > bridge-group-number spanning-disabled on the appropriate interface. If
> RSTP is not disabled on edge
> >
> >
> > ports, convergence times will be excessive for packets traversing those
> ports."
> >
> >
> >
> > 2) It seems RSTP relies on duplex setting to determine inter-switch
> links. What is the configuration to explicitly
> >
> >
> > configure RSTP link types? (I couldnt find this in the documentation)
> >
> >
> >
> > "RSTP can only achieve rapid transition to the forwarding state on edge
> ports and on point-to-point links.
> >
> > The link type is automatically derived from the duplex mode of a port. A
> port that operates in fullduplex
> >
> >
> > is assumed to be point-to-point, while a half-duplex port is considered
> as a shared port by
> >
> > default. This automatic link type setting can be overridden by explicit
> configuration. In switched
> >
> > networks today, most links operate in full-duplex mode and are treated as
> point-to-point links by RSTP.
> >
> >
> > This makes them candidates for rapid transition to the forwarding state."
> >
> >
> >
> > Also i am a bit rough on my RSTP knowledge even after skimming a
> > few Cisco documents. Can someone please explain this in simple way.
> >
> >
> >
> > Thanks in advance
> > _________________________________________________________________
> > Check out the new and improved services from Windows Live. Learn more!
> > http://clk.atdmt.com/UKM/go/132630768/direct/01/
> >
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> >
> > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> >
> >
> >
> >
> >
> >
>
> _________________________________________________________________
> Love Hotmail? Check out the new services from Windows Live!
> http://clk.atdmt.com/UKM/go/132630768/direct/01/
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Sun Mar 01 2009 - 09:44:10 ARST