From: GAURAV MADAN (gauravmadan1177@gmail.com)
Date: Tue Dec 30 2008 - 01:26:49 ARST
Hi All
PLease note that convertible port ( L2 ; L3 using a no switchport /
switchport command ) is not available on HWICs.
HWIC will be either L2 ( like 4ESW ; HWIC-D-9ESW ) or L3 ( like HWIC-1FE and
HWIC-2FE)
For things that u wish ; please take a moment to look in NMs available .
However I am not sure abt cost and what budget u have ..
Gaurav Madan.
On Tue, Dec 30, 2008 at 7:26 AM, Tony Varriale
<tvarriale@flamboyaninc.com>wrote:
> With "no switchport", that would infer a router interface not a switchport.
> That feature is not supported on the HWIC.
>
> And FYI, those old 6500 days aren't gone.
>
> tv
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Tyson Scott
> Sent: Monday, December 29, 2008 6:12 PM
> To: Tony Varriale
> Cc: Hobbs; Cisco certification
> Subject: Re: Cisco 2800s and HWICs
>
> Tony,
>
> I guess all I am saying is configure the port as a layer2 port and
> configure the layer3 interface.
>
> Just the same way as the old hybrid 6500 days.
>
> RTR#sh run int f0/3/0
> interface FastEthernet0/3/0
> switchport trunk native vlan 200
> switchport mode trunk
> switchport voice vlan 400
> end
>
> RTR#sh ip int brief
> Interface IP-Address OK? Method Status
> Protocol
> FastEthernet0/3/0 unassigned YES unset up
> up
> FastEthernet0/3/1 unassigned YES unset up
> down
> FastEthernet0/3/2 unassigned YES unset up
> down
> FastEthernet0/3/3 unassigned YES unset up
> down
> Vlan200 10.10.102.1 YES manual up
> up
> Vlan400 10.10.202.1 YES manual up
> up
>
> On Mon, Dec 29, 2008 at 7:03 PM, Tony Varriale
> <tvarriale@flamboyaninc.com> wrote:
> > Not going to happen. They are l2 only.
> >
> > tv
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> > Hobbs
> > Sent: Monday, December 29, 2008 5:57 PM
> > To: Haroon
> > Cc: Cisco certification
> > Subject: Re: Cisco 2800s and HWICs
> >
> > If cost is an issue I would check get the hwic-4esw if it allows "no
> > switchport". I don't have one to verify. If it's for lab purposes it
> should
> > be fine. An online rack I use has a 2800 with a nm-16esw and it allows
> the
> > no switchport command.
> >
> > Does anyone here know?
> >
> > On Mon, Dec 29, 2008 at 4:39 PM, Haroon <itguy.pro@gmail.com> wrote:
> >
> >> Thanks Hobbs.
> >>
> >> I was just looking at those documents.
> >>
> >> It seems HWIC-1FE would be a better option but are bit expensive
> though,
> >> is anybody selling HWIC-1FE, I need 4 or 5 pieces?
> >>
> >> Thanks,
> >>
> >> Haroon
> >>
> >>
> >> On Mon, Dec 29, 2008 at 6:34 PM, Hobbs <deadheadblues@gmail.com> wrote:
> >>
> >>> Hi,
> >>>
> >>>
> >>>
> >
>
> http://www.cisco.com/en/US/products/ps5854/products_relevant_interfaces_and_
> > modules.html
> >>>
> >>>
> >>>
> >
>
> http://www.cisco.com/en/US/prod/collateral/routers/ps5854/product_data_sheet
> > 0900aecd80581fe6_ps5853_Products_Data_Sheet.html
> >>>
> >>> I believe the switch module interfaces can be converted to routed ports
> >>> with the "no switchport" command. Don't know if all the switch modules
> >>> support it though. Otherwise take a look at the links above for
> HWIC-1FE.
> >>>
> >>> hth
> >>>
> >>> On Mon, Dec 29, 2008 at 3:51 PM, Haroon <itguy.pro@gmail.com> wrote:
> >>>
> >>>> Hello Experts,
> >>>>
> >>>> I have couple of 2811s and few 2821s. I need to add 2 additional
> >>>> Fast-Ethernet interfaces on each of these routers, what is the best
> way
> >>>> to
> >>>> go about doing that? Which module (part#?) would allow layer3
> > capability?
> >>>>
> >>>> I understand HWIC-4ESW would but isn't that a switch which doesn't
> > really
> >>>> do
> >>>> routing on it self but forwards it to the host?
> >>>>
> >>>> Please help.
> >>>>
> >>>> Thanks,
> >>>>
> >>>> Haroon
> >>>>
> >>>>
> >>>> Blogs and organic groups at http://www.ccie.net
> >>>>
> >>>>
> _______________________________________________________________________
> >>>> Subscription information may be found at:
> >>>> http://www.groupstudy.com/list/CCIELab.html
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> > Blogs and organic groups at http://www.ccie.net
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> >
> >
> >
> >
> >
> >
>
>
>
> --
> Tyson Scott - CCIE #13513 R&S and Security
> Technical Instructor - IPexpert, Inc.
>
> Telephone: +1.810.326.1444
> Fax: +1.810.454.0130
> Mailto: tscott@ipexpert.com
>
> Join our free online support and peer group communities:
> http://www.IPexpert.com/communities <http://www.ipexpert.com/communities>
>
> IPexpert - The Global Leader in Self-Study, Classroom-Based, Video On
> Demand and Audio Certification Training Tools for the Cisco CCIE R&S
> Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and
> CCIE Storage Lab Certifications.
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Thu Jan 01 2009 - 12:53:10 ARST