Re: How to monitor with MRM? I get no output when debugging

From: Jason Madsen (madsen.jason@gmail.com)
Date: Sat Nov 29 2008 - 19:33:51 ARST

• Next message: Scott M Vermillion: "OT: GOLD Labs On PEC?"
• Previous message: Modular: "Rip metric in redistribution...."
• Maybe in reply to: Hobbs: "How to monitor with MRM? I get no output when debugging"
• Next in thread: Hobbs: "Re: How to monitor with MRM? I get no output when debugging"
• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

I am no MRM guru, but I do know that with it "no news is good news". It
displays output only when there are problems e.g. packet loss or duplicate
packets.

also, you did start, stop, and then view your report, right?

Jason

On Sat, Nov 29, 2008 at 2:01 PM, Hobbs <deadheadblues@gmail.com> wrote:

> Hello,
>
> I am following the DocCD as well as a couple archives but I cannot seem to
> get this to work. I have the following topology:
>
> R1---ethernet---R2---frame---R5---ethernet---R7---serial---R8---ethernet
>
> R1 is my manager
> R2 is my test sender (LAN interface = 172.31.12.2)
> R7 and R8 are my test receivers (LAN interfaces = 172.31.200.7,172.31.80.8
> )
> R5 is an RP
>
> All LAN interfaces have ip igmp join-group 239.1.1.1
> Pim sparse-dense everywhere and I can ping the group address from any
> router
> above - not sure if this is a requirement for MRM.
>
> R1's config:
>
> access-list 21 permit 172.31.12.2
> access-list 22 permit 172.31.200.7
> access-list 22 permit 172.31.80.8
> ip mrm manager MyTest
> manager FastEthernet0/0 group 239.1.1.1
> senders 21
> receivers 22 no-join
> receivers 22 sender-list 21
>
> R7 and R8 have the test-receiver command on LAN interfaces.
> R2 has the test-sender command on LAN interface.
>
> I debug mrm events and packets but this is all I get on R1:
>
> R1#
> Nov 29 20:54:50.614: MRM: Send Beacon for group 239.1.1.1, holdtime 83400
> seconds
> Nov 29 20:55:50.614: MRM: Send Beacon for group 239.1.1.1, holdtime 83340
> seconds
> Nov 29 20:56:50.614: MRM: Send Beacon for group 239.1.1.1, holdtime 83280
> seconds
>
> Is there something I need to do to generate output?
>
> thanks
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html

Blogs and organic groups at http://www.ccie.net

• Next message: Scott M Vermillion: "OT: GOLD Labs On PEC?"
• Previous message: Modular: "Rip metric in redistribution...."
• Maybe in reply to: Hobbs: "How to monitor with MRM? I get no output when debugging"
• Next in thread: Hobbs: "Re: How to monitor with MRM? I get no output when debugging"
• Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

This archive was generated by hypermail 2.1.4 : Mon Dec 01 2008 - 08:18:32 ARST