From: nouman abbasi (abbasi.nouman@gmail.com)
Date: Wed Oct 01 2008 - 14:32:05 ART
The output of sh ip int brief was wrong ; as it was taken after removing the
config from interface.
Just Frame-relay works, but ppp doesnt work still
any clue
On Wed, Oct 1, 2008 at 7:16 PM, Shaughn Smith <
Shaughn.Smith@za.verizonbusiness.com> wrote:
> Hi
>
> Maybe i am being stupid here but on your config on R4 you have serial
> 0/0 configured but in your sh ip int brief you don't have a serial 0/0.
> That shouldn't be possible unless you haven't included the entire
> output.
>
> Serial0/1 unassigned YES unset administratively
> down
> down
> Serial0/1.24 unassigned YES unset deleted
>
> But basically you need to make sure that your PVC's etc come up and are
> ok.
>
> What I would do is remove the PPP config and just have the PVC on the
> main interface
>
> Then do show frame-relay PVC, once it changes state to active you know
> that your frame-relay configs/switch is working correctly.
>
> Then re-add the ppp and virtual-template configs and all should be ok
>
>
>
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> nouman abbasi
> Sent: Wednesday, October 01, 2008 5:38 PM
> To: ccielab@groupstudy.com
> Subject: PPP over frame-realy
>
> Hello GS,
>
> Can someone help in identifying why Virtual-Template1 doesnt goes Up.??
>
>
> (Question )
> R2 and R should be PPP over frame-realy and should be sub-interface
> but dont use IP unnumbered.
>
> =======
>
> <<R2>>
> ========
>
> interface Serial0/0/1
> no ip address
> encapsulation frame-relay
> no frame-relay inverse-arp
> !
> interface Serial0/0/1.24 point-to-point
> ip address 4.4.24.2 255.255.255.0
> snmp trap link-status
> frame-relay interface-dlci 224 ppp Virtual-Template1
> !
> interface Virtual-Template1
> ip address 4.4.24.2 255.255.255.0
>
>
> ========
> <<R4>>
> ========
>
> interface Serial0/0.24 point-to-point
> ip address 4.4.24.4 255.255.255.0
> snmp trap link-status
> frame-relay interface-dlci 422 ppp Virtual-Template1
> !
> interface Virtual-Template1
> ip address 4.4.24.4 255.255.255.0
> !
>
>
>
> R4#sh ip int bri
> Interface IP-Address OK? Method Status
> Protocol
> Serial0/1 unassigned YES unset administratively
> down
> down
> Serial0/1.24 unassigned YES unset deleted
> down
> Virtual-Access1 unassigned YES unset down
> down
> Virtual-Template1 4.4.24.4 YES manual down
> down
> Virtual-Access2 4.4.24.4 YES TFTP down
> down
>
>
> Blogs and organic groups at http://www.ccie.net
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Sat Nov 01 2008 - 15:35:18 ARST