From: backbone systems (backbone.systems@gmail.com)
Date: Thu Sep 04 2008 - 03:45:18 ART
hmm.Thanks for the inputs.
On Wed, Sep 3, 2008 at 9:09 PM, dara tomar <wish2ie@gmail.com> wrote:
> I agree with Antonio,
>
> It's quite usual that some of the IOS are able to while the others aren't
> able to make the desired markings.
> The logic used to achieve will be correct, but still they don't :| .
>
> Change the IOS and make your observations again, in case you are confident
> that there is no mistake from your side.
>
> Thanks,
> Dara
>
>
>
> On Wed, Sep 3, 2008 at 10:04 PM, Antonio Soares <amsoares@netcabo.pt> wrote:
>>
>> It should work. I've loaded you config and i get the desired output:
>>
>> ++++++++++++++++++++++++++
>> P2#sh policy-map interface
>> Serial1/0
>>
>> Service-policy input: EXP5
>>
>> Class-map: EXP5 (match-all)
>> 10 packets, 1120 bytes
>> 5 minute offered rate 0 bps, drop rate 0 bps
>> Match: mpls experimental topmost 5
>> QoS Set
>> qos-group 5
>> Packets marked 10
>>
>> Class-map: class-default (match-any)
>> 594 packets, 41199 bytes
>> 5 minute offered rate 0 bps, drop rate 0 bps
>> Match: any
>> Serial1/1
>>
>> Service-policy output: MPtoMP
>>
>> Class-map: MPtoMP (match-all)
>> 10 packets, 1120 bytes
>> 5 minute offered rate 0 bps, drop rate 0 bps
>> Match: qos-group 5
>> QoS Set
>> mpls experimental topmost 5
>> Packets marked 10
>>
>> Class-map: class-default (match-any)
>> 770 packets, 52869 bytes
>> 5 minute offered rate 0 bps, drop rate 0 bps
>> Match: any
>> P2#
>> ++++++++++++++++++++++++++
>>
>> Which IOS release and platform are you using ?
>>
>>
>>
>> Regards,
>>
>> Antonio Soares, CCIE #18473 (R&S)
>> amsoares@netcabo.pt
>>
>> -----Original Message-----
>> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
>> backbone systems
>> Sent: quarta-feira, 3 de Setembro de 2008 12:57
>> To: Cisco certification
>> Cc: SP Ccie
>> Subject: MPLS QOS P Router Issue
>>
>> Hi,
>>
>> Below is the config from my P routers. On the Ingress i am marking the
>> traffic to qos-group 5
>> and on the Egress seting the mpls qos topmost to 5
>>
>> All the marking is done for telnet traffic .
>>
>> When i do the show policy-map on the ingress interface i can see the
>> the traffic marked,
>> R3#sh policy-map int ser2/2
>> Serial2/2
>>
>> Service-policy input: EXP5
>>
>> Class-map: EXP5 (match-all)
>> 86 packets, 4586 bytes
>> 5 minute offered rate 0 bps, drop rate 0 bps
>> Match: mpls experimental topmost 5
>> QoS Set
>> qos-group 5
>> Packets marked 86
>>
>> Class-map: class-default (match-any)
>> 815 packets, 56475 bytes
>> 5 minute offered rate 0 bps, drop rate 0 bps
>> Match: any
>>
>> But when i try to see my Egress interface , it is not setting the MPLS
>> EXP bit to 5
>>
>> R3#sh policy-map int ser2/1
>> Serial2/1
>>
>> Service-policy output: MPtoMP
>>
>> Class-map: MPtoMP (match-all)
>> 0 packets, 0 bytes
>> 5 minute offered rate 0 bps, drop rate 0 bps
>> Match: qos-group 5
>> QoS Set
>> mpls experimental topmost 5
>> Packets marked 0
>>
>> Class-map: class-default (match-any)
>> 74 packets, 3978 bytes
>> 5 minute offered rate 0 bps, drop rate 0 bps
>> Match: any
>>
>> Below is the config of my router,
>>
>> R3#sh run
>> Building configuration...
>>
>> Current configuration : 1948 bytes
>> !
>> upgrade fpd auto
>> version 12.4
>> service timestamps debug datetime msec
>> service timestamps log datetime msec
>> no service password-encryption
>> !
>> hostname R3
>> !
>> boot-start-marker
>> boot-end-marker
>> !
>> logging message-counter syslog
>> !
>> no aaa new-model
>> ip source-route
>> ip cef
>> !
>> !
>> !
>> !
>> no ipv6 cef
>> !
>> multilink bundle-name authenticated
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> archive
>> log config
>> hidekeys
>> !
>> !
>> !
>> !
>> !
>> !
>> class-map match-all MPtoMP
>> match qos-group 5
>> class-map match-all EXP5
>> match mpls experimental topmost 5
>> !
>> !
>> policy-map MPtoMP
>> class MPtoMP
>> set mpls experimental topmost 5
>> policy-map EXP5
>> class EXP5
>> set qos-group 5
>> !
>> !
>> !
>> !
>> !
>> interface Loopback0
>> ip address 3.3.3.3 255.255.255.255
>> !
>> interface FastEthernet0/0
>> no ip address
>> shutdown
>> duplex half
>> !
>> interface Serial2/0
>> no ip address
>> encapsulation frame-relay
>> serial restart-delay 0
>> !
>> interface Serial2/0.2 point-to-point
>> ip address 20.0.0.3 255.0.0.0
>> snmp trap link-status
>> mpls ip
>> frame-relay interface-dlci 302
>> !
>> interface Serial2/1
>> ip address 14.0.0.3 255.0.0.0
>> mpls ip
>> serial restart-delay 0
>> service-policy output MPtoMP
>> !
>> interface Serial2/2
>> ip address 13.0.0.3 255.0.0.0
>> mpls ip
>> serial restart-delay 0
>> service-policy input EXP5
>> !
>> interface Serial2/3
>> no ip address
>> shutdown
>> serial restart-delay 0
>> !
>> interface ATM3/0
>> no ip address
>> shutdown
>> no atm ilmi-keepalive
>> !
>> interface Serial4/0
>> no ip address
>> shutdown
>> serial restart-delay 0
>> !
>> interface Serial4/1
>> no ip address
>> shutdown
>> serial restart-delay 0
>> !
>> interface Serial4/2
>> no ip address
>> shutdown
>> serial restart-delay 0
>> !
>> interface Serial4/3
>> no ip address
>> shutdown
>> serial restart-delay 0
>> !
>> router ospf 1
>> log-adjacency-changes
>> network 0.0.0.0 255.255.255.255 area 0
>> !
>> ip forward-protocol nd
>> no ip http server
>> no ip http secure-server
>> !
>> !
>> !
>> logging alarm informational
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> control-plane
>> !
>> !
>> !
>> !
>> !
>> !
>> !
>> gatekeeper
>> shutdown
>> !
>> !
>> line con 0
>> stopbits 1
>> line aux 0
>> stopbits 1
>> line vty 0 4
>> login
>> !
>> end
>>
>>
>> i seems i am doing some basic mistake!!!! Can someone identify that????
>>
>> BB
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>> Blogs and organic groups at http://www.ccie.net
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Sat Oct 04 2008 - 09:26:17 ART