From: Steve Davis (steve.davis@eds.com)
Date: Fri Aug 22 2008 - 13:11:35 ART
This is my 1st post to the list and I'm just getting started wih my quest
for the R&S CCIE. I'm trying to populate my BGP RIB so that I can
redistribute into EIGRP later. The problem is that I can't seem to make the
BGP addresses show up in the BGP Routing Table. I can ping all addresses
without issue.
iBGP
BB1 <--------------> BGP
AS60 AS60
BB1#sh ip bgp summary
Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down
State/PfxRcd
210.15.10.2 4 60 87 87 1 0 0 00:05:26 0
210.15.20.2 4 60 89 89 1 0 0 00:05:29 0
210.15.30.2 4 60 89 89 1 0 0 00:05:29 0
210.15.40.2 4 60 89 89 1 0 0 00:05:30 0
BB1#debug ip packet detail
01:10:40: IP: tableid=0, s=210.15.20.1 (local), d=210.15.20.2 (Serial0/1),
routed via RIB
01:10:40: IP: tableid=0, s=210.15.30.1 (local), d=210.15.30.2 (Serial0/2),
routed via RIB
01:10:40: IP: tableid=0, s=210.15.40.1 (local), d=210.15.40.2 (Serial0/3),
routed via RIB
01:10:40: IP: tableid=0, s=210.16.40.1 (local), d=210.16.40.2 (Serial1/3),
routed via RIB
01:10:40: IP: tableid=0, s=210.17.10.1 (local), d=210.17.10.2 (Serial2/0),
routed via RIB
01:10:40: IP: tableid=0, s=210.17.30.1 (local), d=210.17.30.2 (Serial2/2),
routed via RIB
BB1#sh run | b router bgp 60
router bgp 60
bgp router-id 22.22.22.22
bgp cluster-id 3524249800
bgp log-neighbor-changes
network 22.1.1.1 <==== (Loopback 0 BB1)
network 210.15.10.1
network 210.15.20.1
network 210.15.30.1
network 210.15.40.1
neighbor 20.2.2.2 remote-as 60
neighbor 20.2.2.2 update-source Loopback0
neighbor 210.15.10.2 remote-as 60
neighbor 210.15.10.2 next-hop-self
neighbor 210.15.20.2 remote-as 60
neighbor 210.15.20.2 next-hop-self
neighbor 210.15.30.2 remote-as 60
neighbor 210.15.30.2 next-hop-self
neighbor 210.15.40.2 remote-as 60
neighbor 210.15.40.2 next-hop-self
no auto-summary
I'm seeing the same behavior on the router name BGP.
BGP#sh run | b router bgp 60
router bgp 60
bgp router-id 60.60.60.60
bgp cluster-id 3524249620
bgp log-neighbor-changes
network 20.2.2.2 <===== (loopback 0 BGP)
network 210.15.10.2
network 210.15.20.2
network 210.15.30.2
network 210.15.40.2
neighbor 22.1.1.1 remote-as 60
neighbor 22.1.1.1 update-source Loopback0
neighbor 210.15.10.1 remote-as 60
neighbor 210.15.10.1 update-source Serial0/0
neighbor 210.15.10.1 next-hop-self
neighbor 210.15.20.1 remote-as 60
neighbor 210.15.20.1 next-hop-self
neighbor 210.15.30.1 remote-as 60
neighbor 210.15.30.1 next-hop-self
neighbor 210.15.40.1 remote-as 60
neighbor 210.15.40.1 next-hop-self
no auto-summary
What am I missing?
Blogs and organic groups at http://www.ccie.net
This archive was generated by hypermail 2.1.4 : Mon Sep 01 2008 - 08:15:31 ART