From: Jason Madsen (madsen.jason@gmail.com)
Date: Sun Jul 13 2008 - 12:57:27 ART
one more thought...have you tried physically removing your T1 module and
replacing it...perhaps to a different slot if you have one available?
On Sun, Jul 13, 2008 at 9:55 AM, Jason Madsen <madsen.jason@gmail.com>
wrote:
> if this issue is on warranted devices, you may want to open a TAC case.
> i'm pretty sure many of us would be interested in finding out what the issue
> was, if any, or if it's a bug for that particular IOS and platform. either
> way, good luck.
>
>
> On Sun, Jul 13, 2008 at 3:31 AM, Greg Martin <justler@krweb.net> wrote:
>
>> Same here :). I am sure this issue is probably specific to either IADs
>> or integrated T1 flex controllers. I've done many 1800 series, and 2800
>> series with wic-1dsu-T1 and E1 modules and never ran into this :). I'll
>> just run 12.3 on it!
>>
>>
>> ------------------------------
>>
>> *From:* Jason Madsen [mailto:madsen.jason@gmail.com]
>> *Sent:* Saturday, July 12, 2008 3:03 PM
>> *To:* Greg Martin
>> *Cc:* ccielab@groupstudy.com
>> *Subject:* Re: IAD 2431 w/ T1 ports and 12.4. Keep getting BERT messages
>> when configuring controller
>>
>>
>>
>> that's really weird. i've used T1 modules in 7206s running 12.4 quite a
>> bit and never had any issues such as this. i don't know what to say.
>> honestly i really prefer to stay away from T1s when i can :-)
>>
>>
>>
>> On Sat, Jul 12, 2008 at 12:55 PM, Greg Martin <justler@krweb.net> wrote:
>>
>> Didn't start a BERT test.
>>
>> This only happens on IOS 12.4. I load 12.3 and it's fine. I can't find
>> any
>> Cisco documentation to state why this change was made. There are no BERT
>> commands under the t1 controller.
>>
>> The interfaces are integrated and not WIC modules. I've worked w/ BERT
>> patterns on channelized OC modules before so i'm familiar with the syntax.
>> I just can't figure this one out!
>>
>>
>> -----Original Message-----
>> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
>> Jason Madsen
>> Sent: Saturday, July 12, 2008 12:48 PM
>> To: Greg Martin
>> Cc: ccielab@groupstudy.com
>> Subject: Re: IAD 2431 w/ T1 ports and 12.4. Keep getting BERT messages
>> when
>> configuring controller
>>
>> Did you guys start the T-1 BERT? Do a "show run" and look for any "t1
>> bert" instances to negate. wish i had a T-1 module to test with really
>> quick, but it sounds as though someone started a bert on at least one of
>> your t1s. if you can't find the cmd to negate, you might be able to do
>> "default" xxx global config' command to restore your t1 controller.
>>
>> show controllers t1 bert may give you some info' based on the bert if
>> you're
>> interested.
>>
>> Jason
>>
>> On Sat, Jul 12, 2008 at 4:29 AM, Greg Martin <justler@krweb.net> wrote:
>>
>> > Hey Guys,
>> >
>> >
>> >
>> > I've got an IAD 2431 2xT1/E1 router.
>> >
>> >
>> >
>> > I'm trying to configure the T1 ports but after I enable the card, I go
>> into
>> > the T1 controller and do a channel-group 0 timeslots 1-24 speed 64 and I
>> > get
>> > this message:
>> >
>> >
>> >
>> > %LINK-6-BERTMSGS: Configuration not accepted, BERT is running
>> >
>> >
>> >
>> > Google'd it and came back with nothing.
>> >
>> >
>> >
>> > Running 12.4.18 IP Plus/FW/VOICE
>> >
>> >
>> >
>> > Config:
>> >
>> >
>> >
>> > card type t1 1
>> >
>> > !
>> >
>> > controller t1 1/0
>> >
>> > framing esf
>> >
>> > linecode b8zs
>> >
>> > channel-group 0 timeslots 1-24 speed 64
>> >
>> >
>> >
>> > Then it prints:
>> >
>> >
>> >
>> > %LINK-6-BERTMSGS: Configuration not accepted, BERT is running
>> >
>> >
>> >
>> > It prints this message when I try to modify any commands on the
>> controller.
>> > I've tried plugging in a loop plug so the bert tests could finish, but
>> no
>> > dice.
>> >
>> >
>> >
>> > Can anyone point me in the right direction? I've search over
>> cisco.comand
>> > i've configured hundreds of wic-1dsu-t1/e1/g703 dsu modules and have
>> never
>> > run into this...
>> >
>> >
>> >
>> > Regards,
>> >
>> >
>> >
>> > Greg
>> >
>> >
>> > _______________________________________________________________________
>> > Subscription information may be found at:
>> > http://www.groupstudy.com/list/CCIELab.html
>>
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Mon Aug 04 2008 - 06:11:54 ART