From: GAURAV MADAN (gauravmadan1177@gmail.com)
Date: Sun Jul 13 2008 - 06:43:47 ART
Try aborting the bert on this .. if that works .. ( i guess cli is "
bert abort controller " in EXEC mode )
On Sun, Jul 13, 2008 at 3:01 PM, Greg Martin <justler@krweb.net> wrote:
> Same here :). I am sure this issue is probably specific to either IADs or
> integrated T1 flex controllers. I've done many 1800 series, and 2800 series
> with wic-1dsu-T1 and E1 modules and never ran into this :). I'll just run
> 12.3 on it!
>
>
>
> _____
>
> From: Jason Madsen [mailto:madsen.jason@gmail.com]
> Sent: Saturday, July 12, 2008 3:03 PM
> To: Greg Martin
> Cc: ccielab@groupstudy.com
> Subject: Re: IAD 2431 w/ T1 ports and 12.4. Keep getting BERT messages when
> configuring controller
>
>
>
> that's really weird. i've used T1 modules in 7206s running 12.4 quite a bit
> and never had any issues such as this. i don't know what to say. honestly
> i really prefer to stay away from T1s when i can :-)
>
>
>
>
>
> On Sat, Jul 12, 2008 at 12:55 PM, Greg Martin <justler@krweb.net> wrote:
>
> Didn't start a BERT test.
>
> This only happens on IOS 12.4. I load 12.3 and it's fine. I can't find any
> Cisco documentation to state why this change was made. There are no BERT
> commands under the t1 controller.
>
> The interfaces are integrated and not WIC modules. I've worked w/ BERT
> patterns on channelized OC modules before so i'm familiar with the syntax.
> I just can't figure this one out!
>
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Jason Madsen
> Sent: Saturday, July 12, 2008 12:48 PM
> To: Greg Martin
> Cc: ccielab@groupstudy.com
> Subject: Re: IAD 2431 w/ T1 ports and 12.4. Keep getting BERT messages when
> configuring controller
>
> Did you guys start the T-1 BERT? Do a "show run" and look for any "t1
> bert" instances to negate. wish i had a T-1 module to test with really
> quick, but it sounds as though someone started a bert on at least one of
> your t1s. if you can't find the cmd to negate, you might be able to do
> "default" xxx global config' command to restore your t1 controller.
>
> show controllers t1 bert may give you some info' based on the bert if you're
> interested.
>
> Jason
>
> On Sat, Jul 12, 2008 at 4:29 AM, Greg Martin <justler@krweb.net> wrote:
>
>> Hey Guys,
>>
>>
>>
>> I've got an IAD 2431 2xT1/E1 router.
>>
>>
>>
>> I'm trying to configure the T1 ports but after I enable the card, I go
> into
>> the T1 controller and do a channel-group 0 timeslots 1-24 speed 64 and I
>> get
>> this message:
>>
>>
>>
>> %LINK-6-BERTMSGS: Configuration not accepted, BERT is running
>>
>>
>>
>> Google'd it and came back with nothing.
>>
>>
>>
>> Running 12.4.18 IP Plus/FW/VOICE
>>
>>
>>
>> Config:
>>
>>
>>
>> card type t1 1
>>
>> !
>>
>> controller t1 1/0
>>
>> framing esf
>>
>> linecode b8zs
>>
>> channel-group 0 timeslots 1-24 speed 64
>>
>>
>>
>> Then it prints:
>>
>>
>>
>> %LINK-6-BERTMSGS: Configuration not accepted, BERT is running
>>
>>
>>
>> It prints this message when I try to modify any commands on the
> controller.
>> I've tried plugging in a loop plug so the bert tests could finish, but no
>> dice.
>>
>>
>>
>> Can anyone point me in the right direction? I've search over cisco.comand
>> i've configured hundreds of wic-1dsu-t1/e1/g703 dsu modules and have never
>> run into this...
>>
>>
>>
>> Regards,
>>
>>
>>
>> Greg
>>
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Mon Aug 04 2008 - 06:11:54 ART