From: Muhammad Nasim (muhammad.nasim@gmail.com)
Date: Tue Jun 17 2008 - 08:11:26 ART
Following is the only file in my FLASH
switch: dir flash:
Directory of flash:/
2 -rwx 6433280 <date> c3560-ipbase-mz.122-25.SEE4.bin
9564672 bytes available (6434304 bytes used)
so no config files are present
2008/6/17 Muhammad Nasim <muhammad.nasim@gmail.com>:
> The following is the link in which Passoword recovery is there.
>
> http://www.cisco.com/en/US/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml
>
> I deleted all the files from FLASH. when I went to ROMMON. that means I
> delted all the config files and it should go into the Initial config dialog
> but it is not it is hanging .
>
> after reading the above link i think the startup config stored in FLASH
> which no more there in the flash
>
> I tried with this procesure to install the new image via XMODEM. Image
> installation went well but still it is hanging on the same place
>
>
>
>
>
> 2008/6/17 Alexei Monastyrnyi <alexeim@orcsoftware.com>:
>
> the config files are actually in NVRAM
>>
>> did you try it with password recovery procedure to avoid loading your
>> current config?
>>
>> once you are there in enable mode you can try to "write erase" to wipe
>> out the NVRAM content
>>
>> HTH
>> A.
>>
>> Muhammad Nasim said the following on 6/17/2008 10:33 AM:
>>
>> Actually I format my flash before re-imaging the software. so there is no
>>> config files or any other files in Flash except the image
>>>
>>>
>>> 2008/6/17 Steve <threeseashells@googlemail.com>:
>>>
>>>
>>> Have you tried dropping to ROMMON and manually deleting any startup
>>>> config
>>>> text files? From your output it seems to be powering up ok and failing
>>>> on
>>>> the config. Changing the image won't help as that's loading ok.
>>>>
>>>>
>>>>
>>>> 2008/6/16 Muhammad Nasim <muhammad.nasim@gmail.com>:
>>>>
>>>> I re-imaged the switch but still no luck
>>>>
>>>> any more ideas
>>>>>
>>>>>
>>>>> 2008/6/16 Tyson Scott <tscott@ipexpert.com>:
>>>>>
>>>>>
>>>>> You could still try to do a password recovery to see if it can
>>>>>> recover. Where you are is the last step befor the nvram is loaded so
>>>>>> it is worth testing.
>>>>>>
>>>>>> On Sun, Jun 15, 2008 at 11:13 AM, Muhammad Nasim
>>>>>> <muhammad.nasim@gmail.com> wrote:
>>>>>>
>>>>>> It was a power shut down in the building and then after few mintues
>>>>>>>
>>>>>>> power
>>>>>
>>>>> was up before that the switch was working fine.
>>>>>>>
>>>>>>> Right now there is no configuration on the switch so confgiuration
>>>>>>> can
>>>>>>>
>>>>>>> not
>>>>>>
>>>>>> be a issue
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> 2008/6/15 L Pham <ccie17030@gmail.com>:
>>>>>>>
>>>>>>>
>>>>>>> What happen BEFORE the restart ?
>>>>>>>>
>>>>>>>> On Sun, Jun 15, 2008 at 7:58 AM, Muhammad Nasim
>>>>>>>> <muhammad.nasim@gmail.com> wrote:
>>>>>>>>
>>>>>>>> Dear All,
>>>>>>>>>
>>>>>>>>> I have switch 3560 with 48 ports with POE. It was working fine but
>>>>>>>>>
>>>>>>>>> now
>>>>>
>>>>> after
>>>>>>>>
>>>>>>>> a restart it is hang and below is the output where it hangs. Does
>>>>>>>>>
>>>>>>>>> this
>>>>>
>>>>> happens to anyone. I already changed the image even formated the
>>>>>>>>>
>>>>>>>>> flash
>>>>>
>>>>> and
>>>>>>>>
>>>>>>>> copy new image and boot but no luck still hanging on the same
>>>>>>>>>
>>>>>>>>> output.
>>>>>
>>>>> Below is the output.
>>>>>>>>>
>>>>>>>>> Initializing flashfs...
>>>>>>>>>
>>>>>>>>> flashfs[1]: 1 files, 1 directories
>>>>>>>>> flashfs[1]: 0 orphaned files, 0 orphaned directories
>>>>>>>>> flashfs[1]: Total bytes: 15998976
>>>>>>>>> flashfs[1]: Bytes used: 6434304
>>>>>>>>> flashfs[1]: Bytes available: 9564672
>>>>>>>>> flashfs[1]: flashfs fsck took 1 seconds.
>>>>>>>>> flashfs[1]: Initialization complete....done Initializing flashfs.
>>>>>>>>>
>>>>>>>>> POST: CPU MIC register Tests : Begin
>>>>>>>>> POST: CPU MIC register Tests : End, Status Passed
>>>>>>>>>
>>>>>>>>> POST: PortASIC Memory Tests : Begin
>>>>>>>>> POST: PortASIC Memory Tests : End, Status Passed
>>>>>>>>>
>>>>>>>>> POST: CPU MIC PortASIC interface Loopback Tests : Begin
>>>>>>>>> POST: CPU MIC PortASIC interface Loopback Tests : End, Status
>>>>>>>>>
>>>>>>>>> Passed
>>>>>
>>>>> POST: PortASIC RingLoopback Tests : Begin
>>>>>>>>> POST: PortASIC RingLoopback Tests : End, Status Passed
>>>>>>>>>
>>>>>>>>> POST: Inline Power Controller Tests : Begin
>>>>>>>>> POST: Inline Power Controller Tests : End, Status Passed
>>>>>>>>>
>>>>>>>>> POST: PortASIC CAM Subsystem Tests : Begin
>>>>>>>>> POST: PortASIC CAM Subsystem Tests : End, Status Passed
>>>>>>>>>
>>>>>>>>> POST: PortASIC Port Loopback Tests : Begin
>>>>>>>>> POST: PortASIC Port Loopback Tests : End, Status Passed
>>>>>>>>>
>>>>>>>>> Waiting for Port download...Complete
>>>>>>>>>
>>>>>>>>> cisco WS-C3560-48PS (PowerPC405) processor (revision N0) with
>>>>>>>>>
>>>>>>>>> 118784K/12280K
>>>>>>>>
>>>>>>>> byt
>>>>>>>>> es of memory.
>>>>>>>>> Processor board ID FDO1132Z6AS
>>>>>>>>> Last reset from power-on
>>>>>>>>> 1 Virtual Ethernet interface
>>>>>>>>> 48 FastEthernet interfaces
>>>>>>>>> 4 Gigabit Ethernet interfaces
>>>>>>>>> The password-recovery mechanism is enabled.
>>>>>>>>>
>>>>>>>>> 512K bytes of flash-simulated non-volatile configuration memory.
>>>>>>>>> Base ethernet MAC Address : 00:1D:45:69:CD:80
>>>>>>>>> Motherboard assembly number : 73-9676-12
>>>>>>>>> Power supply part number : 341-0029-05
>>>>>>>>> Motherboard serial number : FDO113202PW
>>>>>>>>> Power supply serial number : LIT11300B61
>>>>>>>>> Model revision number : N0
>>>>>>>>> Motherboard revision number : B0
>>>>>>>>> Model number : WS-C3560-48PS-S
>>>>>>>>> System serial number : FDO1132Z6AS
>>>>>>>>> SFP Module assembly part number : 73-7757-03
>>>>>>>>> SFP Module revision Number : A0
>>>>>>>>> SFP Module serial number : FDO11310AM7
>>>>>>>>> Top Assembly Part Number : 800-25859-03
>>>>>>>>> Top Assembly Revision Number : J0
>>>>>>>>> Version ID : V04
>>>>>>>>> CLEI Code Number : CNMV3N0CRC
>>>>>>>>> Hardware Board Revision Number : 0x01
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> Switch Ports Model SW Version SW Image
>>>>>>>>> ------ ----- ----- ----------
>>>>>>>>>
>>>>>>>>> ----------
>>>>>
>>>>> * 1 52 WS-C3560-48PS 12.2(25)SEE4
>>>>>>>>>
>>>>>>>>> C3560-IPBASE-M
>>>>>>
>>>>>> It hangs here and after that not going any further.
>>>>>>>>>
>>>>>>>>> Any help and inputs required.
>>>>>>>>>
>>>>>>>>> --
>>>>>>>>> Muhammad Nasim
>>>>>>>>> Network Engineer
>>>>>>>>> Saudi Arabia
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>> _______________________________________________________________________
>>>>>>
>>>>>> Subscription information may be found at:
>>>>>>>>> http://www.groupstudy.com/list/CCIELab.html
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>>>>
>>>>>>> --
>>>>>>> Muhammad Nasim
>>>>>>> Network Engineer
>>>>>>> Saudi Arabia
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>> --
>>>>>> Tyson Scott - CCIE #13513 R&S and Security
>>>>>> Technical Instructor - IPexpert, Inc.
>>>>>>
>>>>>> Telephone: +1.810.326.1444
>>>>>> Fax: +1.810.454.0130
>>>>>> Mailto: tscott@ipexpert.com
>>>>>>
>>>>>>
>>>>>>
>>>>> --
>>>>> Muhammad Nasim
>>>>> Network Engineer
>>>>> Saudi Arabia
>>>>>
>>>>>
>>>>>
>>>>>
>>>
>>> --
>>> Muhammad Nasim
>>> Network Engineer
>>> Saudi Arabia
>>>
>>>
>>> _______________________________________________________________________
>>> Subscription information may be found at:
>>> http://www.groupstudy.com/list/CCIELab.html
>>>
>>>
>>>
>>>
>>>
>>>
>> This e-mail is confidential and may contain legally privileged
>> information. It is intended only for the addressees. If you have received
>> this e-mail in error, kindly notify us immediately by telephone or e-mail
>> and delete the message from your system.
>>
>
>
>
> --
> Muhammad Nasim
> Network Engineer
> Saudi Arabia
>
-- Muhammad Nasim Network Engineer Saudi Arabia
This archive was generated by hypermail 2.1.4 : Tue Jul 01 2008 - 06:23:22 ART