From: Farrukh Haroon (farrukhharoon@gmail.com)
Date: Tue Jun 17 2008 - 08:29:16 ART
As others have stated, the config file is in the NVRAM:
SW-F3#dir nvram:
Directory of nvram:/
495 -rw- 15447 <no date> startup-config
496 ---- 5 <no date> private-config
524288 bytes total (508784 bytes free)
Regards
Farrukh
On Tue, Jun 17, 2008 at 2:11 PM, Muhammad Nasim <muhammad.nasim@gmail.com>
wrote:
> Following is the only file in my FLASH
>
> switch: dir flash:
> Directory of flash:/
>
> 2 -rwx 6433280 <date> c3560-ipbase-mz.122-25.SEE4.bin
>
> 9564672 bytes available (6434304 bytes used)
>
> so no config files are present
>
>
> 2008/6/17 Muhammad Nasim <muhammad.nasim@gmail.com>:
>
> > The following is the link in which Passoword recovery is there.
> >
> >
> http://www.cisco.com/en/US/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml
> >
> > I deleted all the files from FLASH. when I went to ROMMON. that means I
> > delted all the config files and it should go into the Initial config
> dialog
> > but it is not it is hanging .
> >
> > after reading the above link i think the startup config stored in FLASH
> > which no more there in the flash
> >
> > I tried with this procesure to install the new image via XMODEM. Image
> > installation went well but still it is hanging on the same place
> >
> >
> >
> >
> >
> > 2008/6/17 Alexei Monastyrnyi <alexeim@orcsoftware.com>:
> >
> > the config files are actually in NVRAM
> >>
> >> did you try it with password recovery procedure to avoid loading your
> >> current config?
> >>
> >> once you are there in enable mode you can try to "write erase" to wipe
> >> out the NVRAM content
> >>
> >> HTH
> >> A.
> >>
> >> Muhammad Nasim said the following on 6/17/2008 10:33 AM:
> >>
> >> Actually I format my flash before re-imaging the software. so there is
> no
> >>> config files or any other files in Flash except the image
> >>>
> >>>
> >>> 2008/6/17 Steve <threeseashells@googlemail.com>:
> >>>
> >>>
> >>> Have you tried dropping to ROMMON and manually deleting any startup
> >>>> config
> >>>> text files? From your output it seems to be powering up ok and failing
> >>>> on
> >>>> the config. Changing the image won't help as that's loading ok.
> >>>>
> >>>>
> >>>>
> >>>> 2008/6/16 Muhammad Nasim <muhammad.nasim@gmail.com>:
> >>>>
> >>>> I re-imaged the switch but still no luck
> >>>>
> >>>> any more ideas
> >>>>>
> >>>>>
> >>>>> 2008/6/16 Tyson Scott <tscott@ipexpert.com>:
> >>>>>
> >>>>>
> >>>>> You could still try to do a password recovery to see if it can
> >>>>>> recover. Where you are is the last step befor the nvram is loaded
> so
> >>>>>> it is worth testing.
> >>>>>>
> >>>>>> On Sun, Jun 15, 2008 at 11:13 AM, Muhammad Nasim
> >>>>>> <muhammad.nasim@gmail.com> wrote:
> >>>>>>
> >>>>>> It was a power shut down in the building and then after few mintues
> >>>>>>>
> >>>>>>> power
> >>>>>
> >>>>> was up before that the switch was working fine.
> >>>>>>>
> >>>>>>> Right now there is no configuration on the switch so confgiuration
> >>>>>>> can
> >>>>>>>
> >>>>>>> not
> >>>>>>
> >>>>>> be a issue
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>> 2008/6/15 L Pham <ccie17030@gmail.com>:
> >>>>>>>
> >>>>>>>
> >>>>>>> What happen BEFORE the restart ?
> >>>>>>>>
> >>>>>>>> On Sun, Jun 15, 2008 at 7:58 AM, Muhammad Nasim
> >>>>>>>> <muhammad.nasim@gmail.com> wrote:
> >>>>>>>>
> >>>>>>>> Dear All,
> >>>>>>>>>
> >>>>>>>>> I have switch 3560 with 48 ports with POE. It was working fine
> but
> >>>>>>>>>
> >>>>>>>>> now
> >>>>>
> >>>>> after
> >>>>>>>>
> >>>>>>>> a restart it is hang and below is the output where it hangs. Does
> >>>>>>>>>
> >>>>>>>>> this
> >>>>>
> >>>>> happens to anyone. I already changed the image even formated the
> >>>>>>>>>
> >>>>>>>>> flash
> >>>>>
> >>>>> and
> >>>>>>>>
> >>>>>>>> copy new image and boot but no luck still hanging on the same
> >>>>>>>>>
> >>>>>>>>> output.
> >>>>>
> >>>>> Below is the output.
> >>>>>>>>>
> >>>>>>>>> Initializing flashfs...
> >>>>>>>>>
> >>>>>>>>> flashfs[1]: 1 files, 1 directories
> >>>>>>>>> flashfs[1]: 0 orphaned files, 0 orphaned directories
> >>>>>>>>> flashfs[1]: Total bytes: 15998976
> >>>>>>>>> flashfs[1]: Bytes used: 6434304
> >>>>>>>>> flashfs[1]: Bytes available: 9564672
> >>>>>>>>> flashfs[1]: flashfs fsck took 1 seconds.
> >>>>>>>>> flashfs[1]: Initialization complete....done Initializing flashfs.
> >>>>>>>>>
> >>>>>>>>> POST: CPU MIC register Tests : Begin
> >>>>>>>>> POST: CPU MIC register Tests : End, Status Passed
> >>>>>>>>>
> >>>>>>>>> POST: PortASIC Memory Tests : Begin
> >>>>>>>>> POST: PortASIC Memory Tests : End, Status Passed
> >>>>>>>>>
> >>>>>>>>> POST: CPU MIC PortASIC interface Loopback Tests : Begin
> >>>>>>>>> POST: CPU MIC PortASIC interface Loopback Tests : End, Status
> >>>>>>>>>
> >>>>>>>>> Passed
> >>>>>
> >>>>> POST: PortASIC RingLoopback Tests : Begin
> >>>>>>>>> POST: PortASIC RingLoopback Tests : End, Status Passed
> >>>>>>>>>
> >>>>>>>>> POST: Inline Power Controller Tests : Begin
> >>>>>>>>> POST: Inline Power Controller Tests : End, Status Passed
> >>>>>>>>>
> >>>>>>>>> POST: PortASIC CAM Subsystem Tests : Begin
> >>>>>>>>> POST: PortASIC CAM Subsystem Tests : End, Status Passed
> >>>>>>>>>
> >>>>>>>>> POST: PortASIC Port Loopback Tests : Begin
> >>>>>>>>> POST: PortASIC Port Loopback Tests : End, Status Passed
> >>>>>>>>>
> >>>>>>>>> Waiting for Port download...Complete
> >>>>>>>>>
> >>>>>>>>> cisco WS-C3560-48PS (PowerPC405) processor (revision N0) with
> >>>>>>>>>
> >>>>>>>>> 118784K/12280K
> >>>>>>>>
> >>>>>>>> byt
> >>>>>>>>> es of memory.
> >>>>>>>>> Processor board ID FDO1132Z6AS
> >>>>>>>>> Last reset from power-on
> >>>>>>>>> 1 Virtual Ethernet interface
> >>>>>>>>> 48 FastEthernet interfaces
> >>>>>>>>> 4 Gigabit Ethernet interfaces
> >>>>>>>>> The password-recovery mechanism is enabled.
> >>>>>>>>>
> >>>>>>>>> 512K bytes of flash-simulated non-volatile configuration memory.
> >>>>>>>>> Base ethernet MAC Address : 00:1D:45:69:CD:80
> >>>>>>>>> Motherboard assembly number : 73-9676-12
> >>>>>>>>> Power supply part number : 341-0029-05
> >>>>>>>>> Motherboard serial number : FDO113202PW
> >>>>>>>>> Power supply serial number : LIT11300B61
> >>>>>>>>> Model revision number : N0
> >>>>>>>>> Motherboard revision number : B0
> >>>>>>>>> Model number : WS-C3560-48PS-S
> >>>>>>>>> System serial number : FDO1132Z6AS
> >>>>>>>>> SFP Module assembly part number : 73-7757-03
> >>>>>>>>> SFP Module revision Number : A0
> >>>>>>>>> SFP Module serial number : FDO11310AM7
> >>>>>>>>> Top Assembly Part Number : 800-25859-03
> >>>>>>>>> Top Assembly Revision Number : J0
> >>>>>>>>> Version ID : V04
> >>>>>>>>> CLEI Code Number : CNMV3N0CRC
> >>>>>>>>> Hardware Board Revision Number : 0x01
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>> Switch Ports Model SW Version SW
> Image
> >>>>>>>>> ------ ----- ----- ----------
> >>>>>>>>>
> >>>>>>>>> ----------
> >>>>>
> >>>>> * 1 52 WS-C3560-48PS 12.2(25)SEE4
> >>>>>>>>>
> >>>>>>>>> C3560-IPBASE-M
> >>>>>>
> >>>>>> It hangs here and after that not going any further.
> >>>>>>>>>
> >>>>>>>>> Any help and inputs required.
> >>>>>>>>>
> >>>>>>>>> --
> >>>>>>>>> Muhammad Nasim
> >>>>>>>>> Network Engineer
> >>>>>>>>> Saudi Arabia
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> _______________________________________________________________________
> >>>>>>
> >>>>>> Subscription information may be found at:
> >>>>>>>>> http://www.groupstudy.com/list/CCIELab.html
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>>>>
> >>>>>>> --
> >>>>>>> Muhammad Nasim
> >>>>>>> Network Engineer
> >>>>>>> Saudi Arabia
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>>>
> >>>>>> --
> >>>>>> Tyson Scott - CCIE #13513 R&S and Security
> >>>>>> Technical Instructor - IPexpert, Inc.
> >>>>>>
> >>>>>> Telephone: +1.810.326.1444
> >>>>>> Fax: +1.810.454.0130
> >>>>>> Mailto: tscott@ipexpert.com
> >>>>>>
> >>>>>>
> >>>>>>
> >>>>> --
> >>>>> Muhammad Nasim
> >>>>> Network Engineer
> >>>>> Saudi Arabia
> >>>>>
> >>>>>
> >>>>>
> >>>>>
> >>>
> >>> --
> >>> Muhammad Nasim
> >>> Network Engineer
> >>> Saudi Arabia
> >>>
> >>>
> >>> _______________________________________________________________________
> >>> Subscription information may be found at:
> >>> http://www.groupstudy.com/list/CCIELab.html
> >>>
> >>>
> >>>
> >>>
> >>>
> >>>
> >> This e-mail is confidential and may contain legally privileged
> >> information. It is intended only for the addressees. If you have
> received
> >> this e-mail in error, kindly notify us immediately by telephone or
> e-mail
> >> and delete the message from your system.
> >>
> >
> >
> >
> > --
> > Muhammad Nasim
> > Network Engineer
> > Saudi Arabia
> >
>
>
>
> --
> Muhammad Nasim
> Network Engineer
> Saudi Arabia
>
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Tue Jul 01 2008 - 06:23:22 ART