From: Muhammad Nasim (muhammad.nasim@gmail.com)
Date: Tue Jun 17 2008 - 08:05:19 ART
The following is the link in which Passoword recovery is there.
http://www.cisco.com/en/US/products/hw/switches/ps628/products_password_recovery09186a0080094184.shtml
I deleted all the files from FLASH. when I went to ROMMON. that means I
delted all the config files and it should go into the Initial config dialog
but it is not it is hanging .
after reading the above link i think the startup config stored in FLASH
which no more there in the flash
I tried with this procesure to install the new image via XMODEM. Image
installation went well but still it is hanging on the same place
2008/6/17 Alexei Monastyrnyi <alexeim@orcsoftware.com>:
> the config files are actually in NVRAM
>
> did you try it with password recovery procedure to avoid loading your
> current config?
>
> once you are there in enable mode you can try to "write erase" to wipe
> out the NVRAM content
>
> HTH
> A.
>
> Muhammad Nasim said the following on 6/17/2008 10:33 AM:
>
> Actually I format my flash before re-imaging the software. so there is no
>> config files or any other files in Flash except the image
>>
>>
>> 2008/6/17 Steve <threeseashells@googlemail.com>:
>>
>>
>> Have you tried dropping to ROMMON and manually deleting any startup
>>> config
>>> text files? From your output it seems to be powering up ok and failing on
>>> the config. Changing the image won't help as that's loading ok.
>>>
>>>
>>>
>>> 2008/6/16 Muhammad Nasim <muhammad.nasim@gmail.com>:
>>>
>>> I re-imaged the switch but still no luck
>>>
>>> any more ideas
>>>>
>>>>
>>>> 2008/6/16 Tyson Scott <tscott@ipexpert.com>:
>>>>
>>>>
>>>> You could still try to do a password recovery to see if it can
>>>>> recover. Where you are is the last step befor the nvram is loaded so
>>>>> it is worth testing.
>>>>>
>>>>> On Sun, Jun 15, 2008 at 11:13 AM, Muhammad Nasim
>>>>> <muhammad.nasim@gmail.com> wrote:
>>>>>
>>>>> It was a power shut down in the building and then after few mintues
>>>>>>
>>>>>> power
>>>>
>>>> was up before that the switch was working fine.
>>>>>>
>>>>>> Right now there is no configuration on the switch so confgiuration can
>>>>>>
>>>>>> not
>>>>>
>>>>> be a issue
>>>>>>
>>>>>>
>>>>>>
>>>>>> 2008/6/15 L Pham <ccie17030@gmail.com>:
>>>>>>
>>>>>>
>>>>>> What happen BEFORE the restart ?
>>>>>>>
>>>>>>> On Sun, Jun 15, 2008 at 7:58 AM, Muhammad Nasim
>>>>>>> <muhammad.nasim@gmail.com> wrote:
>>>>>>>
>>>>>>> Dear All,
>>>>>>>>
>>>>>>>> I have switch 3560 with 48 ports with POE. It was working fine but
>>>>>>>>
>>>>>>>> now
>>>>
>>>> after
>>>>>>>
>>>>>>> a restart it is hang and below is the output where it hangs. Does
>>>>>>>>
>>>>>>>> this
>>>>
>>>> happens to anyone. I already changed the image even formated the
>>>>>>>>
>>>>>>>> flash
>>>>
>>>> and
>>>>>>>
>>>>>>> copy new image and boot but no luck still hanging on the same
>>>>>>>>
>>>>>>>> output.
>>>>
>>>> Below is the output.
>>>>>>>>
>>>>>>>> Initializing flashfs...
>>>>>>>>
>>>>>>>> flashfs[1]: 1 files, 1 directories
>>>>>>>> flashfs[1]: 0 orphaned files, 0 orphaned directories
>>>>>>>> flashfs[1]: Total bytes: 15998976
>>>>>>>> flashfs[1]: Bytes used: 6434304
>>>>>>>> flashfs[1]: Bytes available: 9564672
>>>>>>>> flashfs[1]: flashfs fsck took 1 seconds.
>>>>>>>> flashfs[1]: Initialization complete....done Initializing flashfs.
>>>>>>>>
>>>>>>>> POST: CPU MIC register Tests : Begin
>>>>>>>> POST: CPU MIC register Tests : End, Status Passed
>>>>>>>>
>>>>>>>> POST: PortASIC Memory Tests : Begin
>>>>>>>> POST: PortASIC Memory Tests : End, Status Passed
>>>>>>>>
>>>>>>>> POST: CPU MIC PortASIC interface Loopback Tests : Begin
>>>>>>>> POST: CPU MIC PortASIC interface Loopback Tests : End, Status
>>>>>>>>
>>>>>>>> Passed
>>>>
>>>> POST: PortASIC RingLoopback Tests : Begin
>>>>>>>> POST: PortASIC RingLoopback Tests : End, Status Passed
>>>>>>>>
>>>>>>>> POST: Inline Power Controller Tests : Begin
>>>>>>>> POST: Inline Power Controller Tests : End, Status Passed
>>>>>>>>
>>>>>>>> POST: PortASIC CAM Subsystem Tests : Begin
>>>>>>>> POST: PortASIC CAM Subsystem Tests : End, Status Passed
>>>>>>>>
>>>>>>>> POST: PortASIC Port Loopback Tests : Begin
>>>>>>>> POST: PortASIC Port Loopback Tests : End, Status Passed
>>>>>>>>
>>>>>>>> Waiting for Port download...Complete
>>>>>>>>
>>>>>>>> cisco WS-C3560-48PS (PowerPC405) processor (revision N0) with
>>>>>>>>
>>>>>>>> 118784K/12280K
>>>>>>>
>>>>>>> byt
>>>>>>>> es of memory.
>>>>>>>> Processor board ID FDO1132Z6AS
>>>>>>>> Last reset from power-on
>>>>>>>> 1 Virtual Ethernet interface
>>>>>>>> 48 FastEthernet interfaces
>>>>>>>> 4 Gigabit Ethernet interfaces
>>>>>>>> The password-recovery mechanism is enabled.
>>>>>>>>
>>>>>>>> 512K bytes of flash-simulated non-volatile configuration memory.
>>>>>>>> Base ethernet MAC Address : 00:1D:45:69:CD:80
>>>>>>>> Motherboard assembly number : 73-9676-12
>>>>>>>> Power supply part number : 341-0029-05
>>>>>>>> Motherboard serial number : FDO113202PW
>>>>>>>> Power supply serial number : LIT11300B61
>>>>>>>> Model revision number : N0
>>>>>>>> Motherboard revision number : B0
>>>>>>>> Model number : WS-C3560-48PS-S
>>>>>>>> System serial number : FDO1132Z6AS
>>>>>>>> SFP Module assembly part number : 73-7757-03
>>>>>>>> SFP Module revision Number : A0
>>>>>>>> SFP Module serial number : FDO11310AM7
>>>>>>>> Top Assembly Part Number : 800-25859-03
>>>>>>>> Top Assembly Revision Number : J0
>>>>>>>> Version ID : V04
>>>>>>>> CLEI Code Number : CNMV3N0CRC
>>>>>>>> Hardware Board Revision Number : 0x01
>>>>>>>>
>>>>>>>>
>>>>>>>> Switch Ports Model SW Version SW Image
>>>>>>>> ------ ----- ----- ----------
>>>>>>>>
>>>>>>>> ----------
>>>>
>>>> * 1 52 WS-C3560-48PS 12.2(25)SEE4
>>>>>>>>
>>>>>>>> C3560-IPBASE-M
>>>>>
>>>>> It hangs here and after that not going any further.
>>>>>>>>
>>>>>>>> Any help and inputs required.
>>>>>>>>
>>>>>>>> --
>>>>>>>> Muhammad Nasim
>>>>>>>> Network Engineer
>>>>>>>> Saudi Arabia
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>> _______________________________________________________________________
>>>>>
>>>>> Subscription information may be found at:
>>>>>>>> http://www.groupstudy.com/list/CCIELab.html
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>>>>
>>>>>> --
>>>>>> Muhammad Nasim
>>>>>> Network Engineer
>>>>>> Saudi Arabia
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>> --
>>>>> Tyson Scott - CCIE #13513 R&S and Security
>>>>> Technical Instructor - IPexpert, Inc.
>>>>>
>>>>> Telephone: +1.810.326.1444
>>>>> Fax: +1.810.454.0130
>>>>> Mailto: tscott@ipexpert.com
>>>>>
>>>>>
>>>>>
>>>> --
>>>> Muhammad Nasim
>>>> Network Engineer
>>>> Saudi Arabia
>>>>
>>>>
>>>>
>>>>
>>
>> --
>> Muhammad Nasim
>> Network Engineer
>> Saudi Arabia
>>
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
>>
>>
>>
>>
>>
>>
> This e-mail is confidential and may contain legally privileged information.
> It is intended only for the addressees. If you have received this e-mail in
> error, kindly notify us immediately by telephone or e-mail and delete the
> message from your system.
>
-- Muhammad Nasim Network Engineer Saudi Arabia
This archive was generated by hypermail 2.1.4 : Tue Jul 01 2008 - 06:23:22 ART