From: sakthi somnath (smollin2000@yahoo.com)
Date: Fri Mar 21 2008 - 08:55:55 ART
show interface Serial0/2/0
should there be broadcast queue drops, try increasing
fr broadcast queue-limit.
-Sakthi
--- Shine Joseph <shinepjoseph@iprimus.com.au> wrote:
> Moe,
>
>
>
> That's good.
>
>
>
> Can you swap the DTE/DCE side and apply the clock on
> FR switch rather than
> on the router. See it if that makes a difference. I
> strongly suspect that.
>
>
>
> Regards,
>
> Shine
>
>
>
> _____
>
> From: cisco-addicted
> [mailto:cisco.addicted@gmail.com]
> Sent: Thursday, 20 March 2008 3:49 PM
> To: 'Shine Joseph'; 'But Nicky'; 'Rik Guyler';
> surendratk@hotmail.com;
> 'Jonathan Greenwood II'
> Cc: 'Adel Karim'; 'Envuladu Tsaku';
> steveaggie@gmail.com; 'Cisco
> certification'
> Subject: RE: EIGRP adjacency Flapping
>
>
>
> Dear,
>
> The clock rate on R2 serial because I connected the
> DCE cable from R2 side
> not the FRSW. Is this a problem?? Should all the
> FRSW be the DCE and the
> other routers be DTE??
>
>
>
> And by the way the ping from all the three routers
> on the FR interfaces
> working fine, but when I tried to use the broadcast
> address; only R2 was
> able to ping both spokes.
>
>
>
> The good news that after configuring the neighbor
> command between them, the
> adjacency worked fine ;). But what was the cause of
> the problem????? What if
> they asked me not to use this command ???
>
>
>
> With all regards
>
> Moe
>
>
>
>
>
> !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! R1
> !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
>
>
>
> Rack1R1#ping 183.1.123.2
>
>
>
> Type escape sequence to abort.
>
> Sending 5, 100-byte ICMP Echos to 183.1.123.2,
> timeout is 2 seconds:
>
> !!!!!
>
> Success rate is 100 percent (5/5), round-trip
> min/avg/max = 56/56/60 ms
>
> Rack1R1#
>
> Rack1R1#
>
> Rack1R1#ping 183.1.123.3
>
>
>
> Type escape sequence to abort.
>
> Sending 5, 100-byte ICMP Echos to 183.1.123.3,
> timeout is 2 seconds:
>
> !!!!!
>
> Success rate is 100 percent (5/5), round-trip
> min/avg/max = 112/112/112 ms
>
> Rack1R1#
>
> Rack1R1#
>
> Rack1R1#
>
> Rack1R1#ping 183.1.123.255
>
>
>
> Type escape sequence to abort.
>
> Sending 5, 100-byte ICMP Echos to 183.1.123.255,
> timeout is 2 seconds:
>
>
>
> Reply to request 0 from 183.1.123.2, 84 ms
>
> Reply to request 1 from 183.1.123.2, 84 ms
>
> Reply to request 2 from 183.1.123.2, 84 ms
>
> Reply to request 3 from 183.1.123.2, 84 ms
>
> Reply to request 4 from 183.1.123.2, 84 ms
>
> Rack1R1#
>
> Rack1R1#
>
>
>
>
>
> !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!1 R2
> !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
>
>
>
>
>
> Rack1R2#
>
> Rack1R2#ping 183.1.123.1
>
>
>
> Type escape sequence to abort.
>
> Sending 5, 100-byte ICMP Echos to 183.1.123.1,
> timeout is 2 seconds:
>
> !!!!!
>
> Success rate is 100 percent (5/5), round-trip
> min/avg/max = 56/56/60 ms
>
> Rack1R2#
>
> Rack1R2#
>
> Rack1R2#ping 183.1.123.3
>
>
>
> Type escape sequence to abort.
>
> Sending 5, 100-byte ICMP Echos to 183.1.123.3,
> timeout is 2 seconds:
>
> !!!!!
>
> Success rate is 100 percent (5/5), round-trip
> min/avg/max = 56/56/56 ms
>
> Rack1R2#
>
> Rack1R2#
>
> Rack1R2#
>
> Rack1R2#ping 183.1.123.255
>
>
>
> Type escape sequence to abort.
>
> Sending 5, 100-byte ICMP Echos to 183.1.123.255,
> timeout is 2 seconds:
>
>
>
> Reply to request 0 from 183.1.123.3, 128 ms
>
=== message truncated ===
____________________________________________________________________________________
Be a better friend, newshound, and
know-it-all with Yahoo! Mobile. Try it now. http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ
This archive was generated by hypermail 2.1.4 : Tue Apr 01 2008 - 07:53:54 ART