Re: OSPF Neighbour config wont stick in config ?

From: shiran guez (shiranp3@gmail.com)
Date: Wed Dec 12 2007 - 09:03:56 ART

Next message: avdhesh.goyal@ps.net: "Multicast - backup RP"
Previous message: AKHILESH THAKUR: "RE: RIP Issue - related to link that have diff. networks on"
Maybe in reply to: Alan Ewer: "OSPF Neighbour config wont stick in config ?"
Next in thread: keith tokash: "RE: OSPF Neighbour config wont stick in config ?"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

well I would say that logically it doesn't make sense to put there in the
first place so the developers probably made it to be hidden when you put the
interface into prio 0

if you will remove the ip os prio 0 you will see again your neighbor
statement so it was not remove simply hidden to hint you that it is not
needed, so it is just cosmetics.

On Dec 12, 2007 1:01 PM, Alan Ewer <acewer64@gmail.com> wrote:

> Hi Shiren,
> yes i understand that the neighbour command can be on either location (
> but doesnt need to be on both)..
>
> My Question is
> Why does setting ip ospf pri 0 .. remove the neighbour command from the
> ospf process configuration ??
>
>
> Regds
> Alan E
>
> On Dec 12, 2007 8:53 PM, shiran guez <shiranp3@gmail.com> wrote:
>
> > you do not need a neighbor statement on the spoke of the hub. only on
> > the hub.
> >
> > if you set ip ospf prio 0 this router will never become a DR or BDR so
> > no need to indicate where to unicast
> >
> > On Dec 12, 2007 12:38 PM, Alan Ewer <acewer64@gmail.com> wrote:
> >
> > > Hi All
> > > I have been pondering this little brain teaser ??
> > >
> > > If I have a router configured with the following
> > >
> > > router ospf 1
> > > router id 1.1.1.1
> > > network 1.1.1.0 0.0.0.255 AREA 0
> > > neighbour 1.1.1.2
> > >
> > > ok so far right !!
> > >
> > > Int ser 0/0
> > > ip address 1.1.1.1 255.255.255.0
> > > frame map bla bla bla
> > > ip ospf prio 0
> > >
> > >
> > > and bingo the neighbour command disappears from the OSPF router config
> > > ...
> > > Anyone know why ???
> > >
> > > Regds
> > > Alan E
> > > Brisbane, Aust
> > >
> > > _______________________________________________________________________
> > >
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> > >
> >
> >
> >
> > --
> > Shiran Guez
> > MCSE CCNP NCE1
> > http://cciep3.blogspot.com
> > http://www.linkedin.com/in/cciep3
>
>
>

-- 
Shiran Guez
MCSE CCNP NCE1
http://cciep3.blogspot.com
http://www.linkedin.com/in/cciep3

Next message: avdhesh.goyal@ps.net: "Multicast - backup RP"
Previous message: AKHILESH THAKUR: "RE: RIP Issue - related to link that have diff. networks on"
Maybe in reply to: Alan Ewer: "OSPF Neighbour config wont stick in config ?"
Next in thread: keith tokash: "RE: OSPF Neighbour config wont stick in config ?"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

This archive was generated by hypermail 2.1.4 : Tue Jan 01 2008 - 12:04:30 ARST